How do you replace the Canister Purge Valve and Vapor Canister on Nissan Altima?

Detaching the hoses from the solenoid valve on four-cylinder models mean operating between the firewall and the engine. The electrical connector should be completely detached from the solenoid valve. Thereafter, remove the solenoid valve by first removing its mounting bolts. Then installation is the reverse of removal. In V6 models, it is positioned very high above on the front valve cover for driver side. The two pipes should be separated from that solenoid valve. Disconnect the electrical connector too from this particular solenoid valve. At last, there is a need to remove mounting bolts as well as to extract it out of its socket. Then installation is the reverse of removal. Removing your own EVAP canister can be done if you raise up your automobile and support it properly using jackstands. After that, get rid of mounting bolt then separate canister from EVAP vehicle system through pulling it outwards. Freeing these hoses from a canister should be next step to follow while removingplace switch removed off canister non-water proofed vent passage way towards filling tube with fuel tank under electric current drain-off into gas vapor recovery not safe for environment due emission caused by those dangerous fumes which cause global warming hence it must accept such signal sent via orifice restrictor equipped control omitting any residual vacuum during leakage-proof method evacuation empty sealed system onto capacity measuring device before opening gas cap leave drain all liquid materials down for extended period time according invention place said venting hole connection with opening between filler pipe associated shut-off protection mechanical pressure relief means canceling sealing connections allowing outer atmosphere penetrate actuator other side so quickly maintain even slight overpressure P0449 trouble code indicates malfunction circuit possible causes include damaged harness faulty wiring smoke test confirms purge solenoid leak fault detected where exactly through emissions monitor insufficient voltage reach air-powered activating closed tight like exhalation weak point P0455 large obviously loses tightening state due to its over-large diameter turned out be blocked dirt P0457 indicates loose cap when during refer instructions filling fuel in order ascertain whether it still functioning properly In short, installation is the reverse of removal.

Genuine Nissan Altima Vapor Canister

Fuel Vapor Canister

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Vapor Canisters found

View related parts
Nissan Altima Evaporative Emission Canister
Part Number: 14950-7Y00B
$277.43 MSRP: $391.85
You Save: $114.42 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 14950-7Y00C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2015-2018 Nissan Altima | Base, Entry, S, S PDS, SL, SR, SV, SV Navigation, Tech | 4 Cyl 2.5L, 6 Cyl 3.5L | QR25DE, VQ35DE
View related parts
Nissan Altima Emission Canister Assembly
Part Number: 14950-6CC0A
$283.28 MSRP: $400.12
You Save: $116.84 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CANISTER Assembly E; Vapor Canister
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2019-2024 Nissan Altima | Platinum, S, SL, SR, SV | 4 Cyl 2.5 L GAS, 4 Cyl 2.5L | PR25DD
View related parts
Nissan Altima Emission Canister Assembly
Part Number: 14950-6CC0B
$363.68 MSRP: $513.67
You Save: $149.99 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CANISTER Assembly E; Vapor Canister
- Replaced by: 14950-6CC0C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2019 Nissan Altima | Platinum, S , SL , SR, SV | 4 Cyl 2.5L | PR25DD
View related parts
Nissan Altima Evaporative Emission Canister
Part Number: 14950-4RA0A
$364.68 MSRP: $515.08
You Save: $150.40 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Vapor Canister
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2017-2018 Nissan Altima | S, S PDS, SL, SR, SV, SV Navigation, Tech | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Altima Emission Canister Assembly
Part Number: 14950-9E006
$290.03 MSRP: $409.65
You Save: $119.62 (30%)
ADD TO CART
Product Specifications
- Other Name: Evaporative Emission Canister
- Replaced by: 14950-9E009
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2000 Nissan Altima | GLE, GXE, SE, XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Altima CANISTER Assembly-EVAPORATION
Part Number: 14950-7Y000
$277.43 MSRP: $391.85
You Save: $114.42 (30%)
ADD TO CART
Product Specifications
- Other Name: Evaporative Emission Canister
- Replaced by: 14950-7Y00C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2003-2008 Nissan Altima | Base, S, SE, SE-R, SL, SR | 4 Cyl 2.5L, 6 Cyl 3.5L | QR25DE, VQ35DE
View related parts
Nissan Altima Evaporative Emission Canister
Part Number: 14950-7Y00A
$277.43 MSRP: $391.85
You Save: $114.42 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 14950-7Y00C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2016 Nissan Altima | 25SL/Moon Roof, Base, Entry, S, S PDS, SE, SL, SR, SV, SV Navigation, Tech | 4 Cyl 2.5L, 6 Cyl 3.5L | QR25DE, VQ35DE
View related parts
Nissan Altima Emission Canister Assembly
Part Number: 14950-9J30A
$278.31 MSRP: $393.10
You Save: $114.79 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporative Emission Canister; Vapor Canister
- Replaces: 14950-9J300
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2003-2013 Nissan Altima | Base, S, SL | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Altima CANISTER Assembly EVAPORATION
Part Number: 14950-9E009
$290.03 MSRP: $409.65
You Save: $119.62 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporative Emission Canister; Vapor Canister
- Replaces: 14950-9E008, 14950-9E001, 14950-9E006
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2001 Nissan Altima | GLE, GXE, SE, XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Altima Evaporative Emission Canister
Part Number: 14950-6CC0C
$363.68 MSRP: $513.67
You Save: $149.99 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Vapor Canister
- Replaces: 14950-6CC0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2024 Nissan Altima | Platinum, S, SL, SR, SV | 4 Cyl 2.5 L GAS
View related parts
Nissan Altima Emission Canister Assembly
Part Number: 14950-6CB1A
$282.83 MSRP: $399.48
You Save: $116.65 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CANISTER Assembly E; Vapor Canister
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2019-2024 Nissan Altima | Platinum, SR | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L | KR20DDET
View related parts
Nissan Altima CANISTER Assembly-EVAPORATION
Part Number: 14950-9J300
$278.31 MSRP: $393.10
You Save: $114.79 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporative Emission Canister
- Replaced by: 14950-9J30A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2003-2008 Nissan Altima | Base, S, SL | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Altima CANISTER Assembly-EVAPORATION
Part Number: 14950-9E001
$290.03 MSRP: $409.65
You Save: $119.62 (30%)
ADD TO CART
Product Specifications
- Other Name: Evaporative Emission Canister
- Replaced by: 14950-9E009
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-1999 Nissan Altima | GLE, GXE, SE, XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Altima Emission Canister Assembly
Part Number: 14950-9E008
$290.03 MSRP: $409.65
You Save: $119.62 (30%)
ADD TO CART
Product Specifications
- Other Name: Evaporative Emission Canister
- Replaced by: 14950-9E009
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1999-2001 Nissan Altima | GLE, GXE, SE, XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Altima CANISTER Assembly-EVAPORATION
Part Number: 14950-JA80A
$293.58 MSRP: $414.67
You Save: $121.09 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporative Emission Canister; Vapor Canister
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2011 Nissan Altima | Hybrid | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Altima CANISTER Assembly-EVAPORATION
Part Number: 14950-8J000
$318.34 MSRP: $449.63
You Save: $131.29 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporative Emission Canister; Vapor Canister
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2002-2004 Nissan Altima | Base, S, SE | 4 Cyl 2.5L, 6 Cyl 3.5L | QR25DE, VQ35DE
View related parts
Nissan Altima CANISTER Assembly-EVAPORATION
Part Number: 14950-1E410
Product Specifications
- Other Name: Evaporative Emission Canister; Vapor Canister
- Manufacturer Note: TENNEX
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1993-1997 Nissan Altima | GLE, GXE, SE, XE | 4 Cyl 2.4L | KA24DE

Nissan Altima Vapor Canister

The Altima Vapor Canister is a very important part of the car with refueling vapor control commonly called the EVAP system that assists in reducing pollution in the atmosphere through the storage of fuel vapors from the fuel tank. This new technology helps to improve the performance of the vehicle but it also contributes to the production or assembly line in meeting high emission standards. Comparing the different generations of Nissan Altima models, improvements have been shown in the Vapor Canister through the years for storage and emission of the vapor. When these stored vapors are injected into the fuel-air mixture when the engine needs more fuel, the Vapor Canister plays a central role in enhancing efficiency, thus making the Nissan Altima a car of choice in the market. It can work perfectly with different generations to ensure drivers reap the benefits of improved safety standards and high performance. The Vapor Canister is rather durable and reliable, helping the Nissan Altima to deal with fuel vapors daily. Such reliability is characteristic of the Nissan and strengthens the position of the final car model. Therefore, the Altima Vapor Canister is not only a useful hardware but a proof of efficiency and environmental friendliness that every owner of the Nissan Altima should be proud of. The Altima continues to set standards in the automotive industry, showcasing the importance of the Vapor Canister in its design and functionality.

If you need any OEM Nissan Altima Vapor Canister, feel free to choose them out of our huge selection of genuine Nissan Altima Vapor Canister. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Altima Vapor Canister Parts Questions & Experts Answers

Evaporative Emission Canister
14950-7Y00A
Q: How do you replace the Canister Purge Valve and Vapor Canister on Nissan Altima?
A:
Detaching the hoses from the solenoid valve on four-cylinder models mean operating between the firewall and the engine. The electrical connector should be completely detached from the solenoid valve. Thereafter, remove the solenoid valve by first removing its mounting bolts. Then installation is the reverse of removal. In V6 models, it is positioned very high above on the front valve cover for driver side. The two pipes should be separated from that solenoid valve. Disconnect the electrical connector too from this particular solenoid valve. At last, there is a need to remove mounting bolts as well as to extract it out of its socket. Then installation is the reverse of removal. Removing your own EVAP canister can be done if you raise up your automobile and support it properly using jackstands. After that, get rid of mounting bolt then separate canister from EVAP vehicle system through pulling it outwards. Freeing these hoses from a canister should be next step to follow while removingplace switch removed off canister non-water proofed vent passage way towards filling tube with fuel tank under electric current drain-off into gas vapor recovery not safe for environment due emission caused by those dangerous fumes which cause global warming hence it must accept such signal sent via orifice restrictor equipped control omitting any residual vacuum during leakage-proof method evacuation empty sealed system onto capacity measuring device before opening gas cap leave drain all liquid materials down for extended period time according invention place said venting hole connection with opening between filler pipe associated shut-off protection mechanical pressure relief means canceling sealing connections allowing outer atmosphere penetrate actuator other side so quickly maintain even slight overpressure P0449 trouble code indicates malfunction circuit possible causes include damaged harness faulty wiring smoke test confirms purge solenoid leak fault detected where exactly through emissions monitor insufficient voltage reach air-powered activating closed tight like exhalation weak point P0455 large obviously loses tightening state due to its over-large diameter turned out be blocked dirt P0457 indicates loose cap when during refer instructions filling fuel in order ascertain whether it still functioning properly In short, installation is the reverse of removal.