How to remove the camshaft, camshaft seal, and lash adjuster on the 3.3L V6 Nissan Frontier?

To take out the Lash Adjusters, begin by removing the valve cover and rocker arm shaft assemblies. Use rubber bands to keep them in place so that they don't come off from their guides. The Lash Adjuster guide assembly is then removed and Lash Adjusters are taken out of the bores one at a time, keeping them in order. They should not be laid on their side or upside down to avoid trapping air inside. If you feel like there is trapped air, put back the rocker arms, shafts as well as, valve covers and run the engine for 10 minutes at 1000 rpm to bleed the air out of the Lash Adjusters. While they are outside of the engine, check for wear by examining them again so that you can replace if needed. To get rid of camshafts remove heads and pry camshaft cover plate gently from there (Gillespie 7). When unscrewing retaining bolt hold it with holding lugs tightening it accordingly till you remove thrust plate and bolt. The camshaft oil seal should be removed with caution to prevent scuffing or scratching it as it is being pulled out. By rotating in twist squeeze motion pull oronsealpacificcamshaft out of cylinder head (Olay/Weisman Architects). Camshafts are lubricated on bearing journals and lobes using moly-based engine assembly lube before they are cautiously placed into position in the cylinder head (Olay/Weisman Architects). Install camshaft thrust plates with their retaining bolts and ensure that I have checked if my camshafts have any end play (Olay/Weisman Architects). In case endplay does not fall within certain range then thrust plate has to be replaced (Olay/Weisman Architects). Set up camshaft oil seal thus finishing assembling cylinder head.

Genuine Nissan Frontier Camshaft Seal

Cam Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Camshaft Seals found

View related parts
Nissan Frontier Seal-Oil,Camshaft
Part Number: 13042-3HD0A
$10.61 MSRP: $14.10
You Save: $3.49 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Seal
- Manufacturer Note: ALTERNATIVE: 13042-3
- Replaces: 13042-6N200, 13042-3HD0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2019 Nissan Frontier | S, SE, SV, XE | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Frontier Seal-Oil,Camshaft
Part Number: 13042-0B001
$11.22 MSRP: $16.25
You Save: $5.03 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Seal
- Replaces: 13042-D0100, 13042-0B000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2004 Nissan Frontier | SC, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Seal-Oil,Camshaft
Part Number: 13042-6N200
$10.61 MSRP: $14.10
You Save: $3.49 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 13042-3HD0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2012 Nissan Frontier | SE, SV, XE | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Frontier Oil Seal
Part Number: 13510-10Y00
$12.40 MSRP: $17.52
You Save: $5.12 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal-Oil,Crankshaft Front
- Replaced by: 13510-10Y12
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2001 Nissan Frontier | SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Seal-Oil,Crankshaft Front
Part Number: 13510-V7201
$12.40 MSRP: $17.52
You Save: $5.12 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Position: Front
- Replaced by: 13510-10Y12
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Frontier | SC, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Oil Seal-Can
Part Number: 13042-6CA0A
$7.64 MSRP: $11.07
You Save: $3.43 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Seal
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2024 Nissan Frontier | Hardbody Edition, PRO-4X, PRO-X, S, SL, SV | 6 Cyl 3.8 L GAS

Nissan Frontier Camshaft Seal

The Camshaft Seal in your Nissan Frontier will prevent contaminants from entering the passage the camshaft uses to exit the cylinder head. It will also preserve clean oil inside the passage that is applied to lubricate the camshaft. This will assist in reliable valve timing. The seal creates a tight barrier around the rotating camshaft journal. It prevents dirt, debris, and engine oil leaks from interfering with the proper opening and closing of valves driven by the cam. The Camshaft Seal keeps the lubricant within the bearing surfaces to keep the crankshaft driven cam in concert with the crankshaft at one-half crankshaft speed to provide for smooth combustion cycles. The Camshaft Seal is located at the cylinder head and rotates continuously while remaining stable to help promote engine efficiency in every Nissan Frontier application. This straightforward design provides the same protection across the Nissan lineup. Routine replacement of a worn Camshaft Seal on a Frontier engine will prevent oil seepage. Periodic service intervals that include inspection of the Camshaft Seal assist in ongoing delivery of power and fuel economy of the Nissan Frontier.

If you need any OEM Nissan Frontier Camshaft Seal, feel free to choose them out of our huge selection of genuine Nissan Frontier Camshaft Seal. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Frontier Camshaft Seal Parts Questions & Experts Answers

Seal-Oil,Camshaft
13042-0B001
Q: How to remove the camshaft, camshaft seal, and lash adjuster on the 3.3L V6 Nissan Frontier?
A:
To take out the Lash Adjusters, begin by removing the valve cover and rocker arm shaft assemblies. Use rubber bands to keep them in place so that they don't come off from their guides. The Lash Adjuster guide assembly is then removed and Lash Adjusters are taken out of the bores one at a time, keeping them in order. They should not be laid on their side or upside down to avoid trapping air inside. If you feel like there is trapped air, put back the rocker arms, shafts as well as, valve covers and run the engine for 10 minutes at 1000 rpm to bleed the air out of the Lash Adjusters. While they are outside of the engine, check for wear by examining them again so that you can replace if needed. To get rid of camshafts remove heads and pry camshaft cover plate gently from there (Gillespie 7). When unscrewing retaining bolt hold it with holding lugs tightening it accordingly till you remove thrust plate and bolt. The camshaft oil seal should be removed with caution to prevent scuffing or scratching it as it is being pulled out. By rotating in twist squeeze motion pull oronsealpacificcamshaft out of cylinder head (Olay/Weisman Architects). Camshafts are lubricated on bearing journals and lobes using moly-based engine assembly lube before they are cautiously placed into position in the cylinder head (Olay/Weisman Architects). Install camshaft thrust plates with their retaining bolts and ensure that I have checked if my camshafts have any end play (Olay/Weisman Architects). In case endplay does not fall within certain range then thrust plate has to be replaced (Olay/Weisman Architects). Set up camshaft oil seal thus finishing assembling cylinder head.