How to properly remove and reinstall the Transmission Assembly along with the torque converter as a single assembly on Nissan Frontier?

The transmission and torque converter must be removed as a single assembly. If you try to leave the torque converter attached to the drive plate, it will cause damage. The drive plate is not designed to bear weight. First, disconnect the cable from the negative terminal of the battery. Raise the vehicle and support it on jack stands, removing the skid plate and skid plate crossmember if equipped. Drain the transmission fluid. On a four-cylinder Frontier model, detach the Throttle Valve cable from the transmission and temporarily reinstall the transmission fluid pan. Detach the shift cable from the manual lever and bracket. Mark the yokes and remove the driveshaft; on 4WD models, remove both driveshafts. Remove obstructive exhaust components, the Crankshaft Position sensor, and the starter motor. Trace the wiring harnesses from the transmission and disconnect them. Remove the inspection cover and mark the relationship of the torque converter to the drive plate. Extract the torque converter-to-drive plate bolts, turning the crankshaft for access. Extract the fill/dipstick tube and its bracket. Detach the fluid cooler lines from the transmission, discarding sealing washers. On 4WD models, remove the transfer case, though if the main aim isn't transmission replacement, one might keep the transfer case attached. Just disconnect the shift rod and the electrical connectors from the speed sensors, and detach the vent tube. Support both the engine and transmission using appropriate jacks. Remove the bolt holding the transmission mount to the cross member. Lower both slightly, then unbolt the transmission from the engine. Slide the transmission back to disengage it from the engine block dowel pins, ensuring the torque converter is detached. Clamp locking pliers on the bell housing to prevent the converter from falling. For installation, confirm the torque converter's engagement in the pump. If you've detached it, lubricate the converter rear hub and install it onto the front input shaft. Raise the transmission into position and align the holes of the torque converter with those in the drive plate. Carefully push the transmission forward, ensuring dowel pins engage with the bell housing. Mate the transmission with the engine without gaps. Install and tighten all bolts while verifying a complete mate between the engine and transmission. Raise the transmission's rear end, reattaching the cross member. Remove supporting jacks. Reconnect the torque converter-to-drive plate bolts and reinstall the dipstick tube. Reattach the starter motor and torque converter inspection cover. With new sealing washers, reconnect the transmission fluid cooler lines and the transmission's electrical connectors. Reconnect the shift cable, and on 4WD models, reinstall the transfer case. Reattach the driveshaft(s) and adjust the shift cable. On four-cylinder Frontier models, reconnect the Throttle Valve cable, install the fluid pan with a fresh gasket, and tighten its bolts. Reattach any removed exhaust components, lower the vehicle, and refill the transmission with the specified fluid. Finally, run the engine and check for any fluid leaks.

Genuine Nissan Frontier Transmission Assembly

Trans Assembly

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

93 Transmission Assemblies found

View related parts
Nissan Frontier Automatic Transmission Assembly
Part Number: 310C0-43X64
$1885.40 MSRP: $2262.23
You Save: $376.83 (17%)
ADD TO CART
Limited Availability
Product Specifications
- Other Name: Transmission Assembly-Auto
- Replaced by: 3102M-43X64RE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1999-2003 Nissan Frontier | SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZP41ARA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 310CM-ZP40ERA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2007 Nissan Frontier | LE, Off-Road, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Manual Transmission
Part Number: 32010-EA000
$2642.17 MSRP: $3198.76
You Save: $556.59 (18%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Transmission Assy; Transmission
- Manufacturer Note: QR25 5MT (2WD)
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2019 Nissan Frontier | S, SE, SV, XE | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZP85ERA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Reman Transmission Assy-Autom ; Automatic Transmission Assy-Reman
- Replaces: 310CM-ZP85DRA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2006-2009 Nissan Frontier | LE, Off-Road, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZP60DRA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 310CM-ZP60CRA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2006-2009 Nissan Frontier | LE, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZS47ARA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 310CM-ZS46DRA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2006-2009 Nissan Frontier | LE, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZS04CRA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 310CM-ZS04BRA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2006-2009 Nissan Frontier | LE, Off-Road, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZP11ARA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 310CM-ZP10ERA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2007 Nissan Frontier | LE, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZP65DRA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 310CM-ZP65CRA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2006-2009 Nissan Frontier | LE, Off-Road, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-EA10CRA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 3102M-EA10BRE, 310CM-EA10BRE, 310CM-EA10ARE, 310CM-EA10BRA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2006 Nissan Frontier | LE, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZP01ARA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 310CM-ZP00ERA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2007 Nissan Frontier | LE, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-EA30CRA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 3102M-EA30ARE, 3102M-EA30BRE, 310CM-EA30BRA, 310CM-EA30BRE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2006 Nissan Frontier | LE, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZP31ARA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 310CM-ZP30ERA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2007 Nissan Frontier | LE, Off-Road, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZP80ERA
$3477.20 MSRP: $4189.34
You Save: $712.14 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 310CM-ZP80DRA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2006-2009 Nissan Frontier | LE, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-EA50CRA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 3102M-EA50ARE, 310CM-EA50BRE, 310CM-EA50BRA, 3102M-EA50BRE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2006 Nissan Frontier | LE, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-EA20CRA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 3102M-EA20BRE, 310CM-EA20BRE, 310CM-EA20ARE, 310CM-EA20BRA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2006 Nissan Frontier | LE, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Blank Automatic Transmission
Part Number: 310C0-61X5D
$4401.51 MSRP: $5328.70
You Save: $927.19 (18%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission-W/O Programming
- Replaces: 31020-61X5D
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2006-2009 Nissan Frontier | LE, Off-Road, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZS50CRA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 310CM-ZS50BRA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2006-2009 Nissan Frontier | LE, Off-Road, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Reman Automatic Transmission Assembly
Part Number: 310CM-ZS01ARA
$3344.11 MSRP: $4028.21
You Save: $684.10 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Assy-Reman
- Replaces: 310CM-ZS00DRA
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2009 Nissan Frontier | LE, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Blank Automatic Transmission
Part Number: 31020-61X3C
$6019.16 MSRP: $7287.11
You Save: $1267.95 (18%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Transmission
- Manufacturer Note: W/OUT ROM DATA (2WD) QR25
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2010-2019 Nissan Frontier | S, SE, SV, XE | 4 Cyl 2.5L | QR25DE

| Page 1 of 5 |Next >

1-20 of 93 Results

Nissan Frontier Transmission Assembly

The Nissan Frontier Transmission Assembly gives the midsize truck the ability to convert engine power into smooth, usable motion across every driving situation. As a connecting link from the crankshaft to the wheels, the Transmission Assembly multiplies the engine's torque by utilizing selectable gear ratios, making a hill climb easier. Low revs and fuel consumption occur on the highway. Over time, the pickup has catered for several styles of Transmission Assembly. Many Frontier drivers like traditional stick shift versions. These use sliding gears and parallel shafts with which the driver can coordinate with a clutch pedal for direct control. Numerous Nissan models come with automatic editions that utilize hydraulic pressure, a fluid coupling to operate the transmission, and compact planetary gearsets that a computer supervises. In other words, it covers self-shifting convenience. The Transmission Assembly option lets you also have a continuously variable unit that replaces fixed cogs with a belt and pulleys to keep the engine at its sweet rpm, plus a dual clutch system that preselects the next ratio for lightning quick changes. All types of Transmission Assembly must be leak-free, shift clean, and not emit any weird grinding noises. If ignored, it won't take long for any Nissan Frontier to get sidelined.

If you need any OEM Nissan Frontier Transmission Assembly, feel free to choose them out of our huge selection of genuine Nissan Frontier Transmission Assembly. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Frontier Transmission Assembly Parts Questions & Experts Answers

Manual Transmission
32010-4S110
Q: How to properly remove and reinstall the Transmission Assembly along with the torque converter as a single assembly on Nissan Frontier?
A:
The transmission and torque converter must be removed as a single assembly. If you try to leave the torque converter attached to the drive plate, it will cause damage. The drive plate is not designed to bear weight. First, disconnect the cable from the negative terminal of the battery. Raise the vehicle and support it on jack stands, removing the skid plate and skid plate crossmember if equipped. Drain the transmission fluid. On a four-cylinder Frontier model, detach the Throttle Valve cable from the transmission and temporarily reinstall the transmission fluid pan. Detach the Shift Cable from the manual lever and bracket. Mark the yokes and remove the driveshaft; on 4WD models, remove both driveshafts. Remove obstructive exhaust components, the Crankshaft Position sensor, and the starter motor. Trace the wiring harnesses from the transmission and disconnect them. Remove the inspection cover and mark the relationship of the torque converter to the drive plate. Extract the torque converter-to-drive plate bolts, turning the crankshaft for access. Extract the fill/dipstick tube and its bracket. Detach the fluid cooler lines from the transmission, discarding sealing washers. On 4WD models, remove the Transfer Case, though if the main aim isn't transmission replacement, one might keep the transfer case attached. Just disconnect the shift rod and the electrical connectors from the speed sensors, and detach the vent tube. Support both the engine and transmission using appropriate jacks. Remove the bolt holding the transmission mount to the cross member. Lower both slightly, then unbolt the transmission from the engine. Slide the transmission back to disengage it from the engine block dowel pins, ensuring the torque converter is detached. Clamp locking pliers on the bell housing to prevent the converter from falling. For installation, confirm the torque converter's engagement in the pump. If you've detached it, lubricate the converter rear hub and install it onto the front input shaft. Raise the transmission into position and align the holes of the torque converter with those in the drive plate. Carefully push the transmission forward, ensuring dowel pins engage with the bell housing. Mate the transmission with the engine without gaps. Install and tighten all bolts while verifying a complete mate between the engine and transmission. Raise the transmission's rear end, reattaching the cross member. Remove supporting jacks. Reconnect the torque converter-to-drive plate bolts and reinstall the dipstick tube. Reattach the starter motor and torque converter inspection cover. With new sealing washers, reconnect the transmission fluid cooler lines and the transmission's electrical connectors. Reconnect the shift cable, and on 4WD models, reinstall the transfer case. Reattach the driveshaft(s) and adjust the shift cable. On four-cylinder Frontier models, reconnect the Throttle Valve cable, install the fluid pan with a fresh gasket, and tighten its bolts. Reattach any removed exhaust components, lower the vehicle, and refill the transmission with the specified fluid. Finally, run the engine and check for any fluid leaks.