How to check and repack the front wheel hub and wheel bearings on Nissan Pathfinder?

The front wheel bearings must be checked and repacked. For this, you need to have jackstands that can support the vehicle safely, torque wrench, grease hammer, wood block, needle nose pliers, grease gun, socket/breaker bar hammer, screwdriver and brush. Begin by spinning each wheel to check for noise, rolling resistance and endplay. If any detectable movement occurs when moving the wheel in and out on the spindle is observed then the bearings should be inspected and either packed with grease or replaced as necessary. Take out disc brake caliper and caliper mounting bracket after removing wheel. On ABS equipped vehicles remove front wheel speed sensors while in case of 4WD models remove free running hub if present. In case of 2WD Frontier models remove hub cap followed by cotter pin spindle nut as well as thrust washer. On 4WD frontier models also all Xterras and pathfinders remove lockwasher screws lockwasher along with locknut using a special tool then pull hub assembly off spindle. Pry rear seal from hub assembly, remove inner wheel bearing and clean out all old grease from bearings, hub, spindle using solvent. Examine races and bearings for damage; replace them as matched sets if necessary. Pack bearings with high temperature front wheel bearing grease; apply grease to the spindle and hub races. Put together again the hub assembly while for 2WD Frontier models follow specific procedures for tightening of spindle nut torque as follows; tighten the locknut to specified torques for 4WD Frontier models plus all Xterras & Pathfinders measuring wheel bearing preload adjust respectively according to need). Finish installments by performing reverse steps while ensuring proper torque of lugs nuts on wheels plus attachment of hub cap in place.

Genuine Nissan Pathfinder Wheel Hub

Wheel Axle Hub

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

33 Wheel Hubs found

View related parts
Nissan Pathfinder Hub Assembly Road Wheel
Part Number: 40202-3JA1A
$187.74 MSRP: $277.98
You Save: $90.24 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 40202-JA100, 40202-ZX70A, 40202-ZX10A, 40202-3JA0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2020 Nissan Pathfinder | Platinum, Platinum Hybrid, S, SL, SL Hybrid, SV, SV Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5L, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L | QR25DER, VQ35DD, VQ35DE
View related parts
Nissan Pathfinder Hub Assembly Road Wheel
Part Number: 40202-4X01A
$233.15 MSRP: $339.87
You Save: $106.72 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Replaced by: 40202-9BT1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2012 Nissan Pathfinder | LE, S, SE, Silver Edition, SV | 6 Cyl 4.0L, 8 Cyl 5.6L | VK56DE, VQ40DE
View related parts
Nissan Pathfinder Road Wheel Hub Assembly Front
Part Number: 40202-3JA0A
$187.74 MSRP: $277.98
You Save: $90.24 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Position: Front
- Replaced by: 40202-3JA1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2017 Nissan Pathfinder | Platinum, S, SL, SV | 4 Cyl 2.5L, 6 Cyl 3.5L | QR25DER, VQ35DE
View related parts
Nissan Pathfinder Hub Assembly Rear
Part Number: 43202-3JA1B
$217.14 MSRP: $321.52
You Save: $104.38 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Axle
- Position: Rear
- Replaced by: 43202-3JA1D
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2019 Nissan Pathfinder | Platinum, S, SL, SV | 6 Cyl 3.5L | VQ35DD
View related parts
Nissan Pathfinder Hub Assembly Road Wheel
Part Number: 40202-4X00A
$262.74 MSRP: $401.00
You Save: $138.26 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Replaced by: 40202-9BT0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2012 Nissan Pathfinder | LE, S, SE, Silver Edition, SV | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Pathfinder Road Wheel Hub Assembly Front
Part Number: 40202-EA300
$233.15 MSRP: $339.87
You Save: $106.72 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Position: Front
- Replaced by: 40202-9BT1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2008 Nissan Pathfinder | LE, S, SE, SE Off-Road, XE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Pathfinder Hub Assembly Road Wheel
Part Number: 40202-0W094
$247.49 MSRP: $366.45
You Save: $118.96 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front; Front Hub, Hub Assembly
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1999-2004 Nissan Pathfinder | LE, SE, XE | 6 Cyl 3.3L, 6 Cyl 3.5L | VG33E, VQ35DE
View related parts
Nissan Pathfinder Rear Hub Assembly
Part Number: 43202-3JA0A
$180.48 MSRP: $267.23
You Save: $86.75 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Axle
- Manufacturer Note: SAME AS 43202-JA000
- Position: Rear
- Replaced by: 43202-3JA1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2015 Nissan Pathfinder | Platinum, S, SL, SV | 4 Cyl 2.5L, 6 Cyl 3.5L | QR25DER, VQ35DE
View related parts
Nissan Pathfinder Rear Hub Assembly
Part Number: 43202-3JA0B
$217.14 MSRP: $321.52
You Save: $104.38 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Axle
- Position: Rear
- Replaced by: 43202-3JA1D
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2017 Nissan Pathfinder | Platinum, S, SL, SV | 4 Cyl 2.5L, 6 Cyl 3.5L | QR25DER, VQ35DE
View related parts
Nissan Pathfinder Road Wheel Hub Assembly Front
Part Number: 40202-ZP90A
$233.15 MSRP: $339.87
You Save: $106.72 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Position: Front
- Replaced by: 40202-9BT1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2010 Nissan Pathfinder | LE, S, SE, SE Off-Road, SV, XE | 6 Cyl 4.0L, 8 Cyl 5.6L | VK56DE, VQ40DE
View related parts
Nissan Pathfinder Hub Assembly Rear
Part Number: 43202-4X00A
$242.93 MSRP: $342.57
You Save: $99.64 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Axle; Hub, Hub Assembly
- Position: Rear
- Replaces: 43202-EA500, 43202-ZP80A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2012 Nissan Pathfinder | LE, S, SE, SE Off-Road, Silver Edition, SV, XE | 6 Cyl 4.0L, 8 Cyl 5.6L | VK56DE, VQ40DE
View related parts
Nissan Pathfinder Road Wheel Hub Assembly Front
Part Number: 40202-EA000
$262.74 MSRP: $401.00
You Save: $138.26 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Position: Front
- Replaced by: 40202-9BT0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2008 Nissan Pathfinder | LE, S, SE, SE Off-Road, XE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Pathfinder Rear Hub Assembly
Part Number: 43202-EA500
$242.93 MSRP: $342.57
You Save: $99.64 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Axle
- Position: Rear
- Replaced by: 43202-4X00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2008 Nissan Pathfinder | LE, S, SE, SE Off-Road, XE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Pathfinder Road Wheel Hub Assembly Front
Part Number: 40202-6SA0A
$240.21 MSRP: $349.80
You Save: $109.59 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front; Front Hub & Bearing, Hub Assembly
- Position: Front
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2022-2025 Nissan Pathfinder | Platinum, Rock Creek, S, SL, SV | 6 Cyl 3.5 L GAS
View related parts
Nissan Pathfinder Hub Assembly Rear
Part Number: 43202-3JA0C
$197.51 MSRP: $292.45
You Save: $94.94 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Axle
- Position: Rear
- Replaces: 43202-3JA1C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2020 Nissan Pathfinder | Platinum, S, SL, SV | 4 Cyl 2.5L, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L | QR25DER, VQ35DD, VQ35DE
View related parts
Nissan Pathfinder Hub Assembly-Rear Axle
Part Number: 43202-3JA1D
$217.14 MSRP: $321.52
You Save: $104.38 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Rear
- Replaces: 43202-3JA1B, 43202-3JA0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020 Nissan Pathfinder | Platinum, Platinum Hybrid, S, SL, SL Hybrid, SV, SV Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
Nissan Pathfinder Rear Hub Assembly
Part Number: 43202-ZP80A
$242.93 MSRP: $342.57
You Save: $99.64 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Axle
- Position: Rear
- Replaced by: 43202-4X00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2010 Nissan Pathfinder | LE, S, SE, SE Off-Road, SV, XE | 6 Cyl 4.0L, 8 Cyl 5.6L | VK56DE, VQ40DE
View related parts
Nissan Pathfinder Hub Assembly Rear
Part Number: 43202-3JA1C
$197.51 MSRP: $292.45
You Save: $94.94 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Axle
- Position: Rear
- Replaced by: 43202-3JA0C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2019 Nissan Pathfinder | Platinum, S, SL, SV | 6 Cyl 3.5L | VQ35DD
View related parts
Nissan Pathfinder Road Wheel Hub Assembly Front
Part Number: 40202-ZP50A
$262.74 MSRP: $401.00
You Save: $138.26 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Position: Front
- Replaced by: 40202-9BT0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2010 Nissan Pathfinder | LE, S, SE, SE Off-Road, SV, XE | 6 Cyl 4.0L, 8 Cyl 5.6L | VK56DE, VQ40DE
View related parts
Nissan Pathfinder Hub Assembly Road Wheel
Part Number: 40202-1W092
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Replaced by: 40202-1W093
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2000 Nissan Pathfinder | LE, SE, XE | 6 Cyl 3.3L | VG33E

| Page 1 of 2 |Next >

1-20 of 33 Results

Nissan Pathfinder Wheel Hub

Nissan Pathfinder Wheel Hub serves as the secure mounting point between the vehicle's axle assembly and its wheel, allowing smooth rotation while keeping the wheel firmly attached. The hub sits between the drive axle and brake disc or drum, holding bearings that reduce friction and support both steering control and safety. Inside the Wheel Hub, roller or unit bearings let the wheel turn freely. Their condition is vital for performance and stability. Many modern units use an integral Wheel Hub and bearing assembly that can include an ABS sensor and is replaced as a single piece when worn. Other configurations described include variants that separate the hub and bearing with press fitting and non-driven axle hubs that house tapered roller bearings, though each still performs the same core task on a Pathfinder. Constructed from material and secured by bolts and studs, the Nissan Wheel Hub provides a base for brake rotors, calipers, and sensors, ensuring dependable wheel alignment on every Pathfinder. Proper torque on the Wheel Hub fasteners helps the Nissan Pathfinder maintain handling. This component meets Nissan strength standards.

If you need any OEM Nissan Pathfinder Wheel Hub, feel free to choose them out of our huge selection of genuine Nissan Pathfinder Wheel Hub. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Pathfinder Wheel Hub Parts Questions & Experts Answers

Hub Assembly Road Wheel
40202-0W094
Q: How to check and repack the front wheel hub and wheel bearings on Nissan Pathfinder?
A:
The front wheel bearings must be checked and repacked. For this, you need to have jackstands that can support the vehicle safely, torque wrench, grease hammer, wood block, needle nose pliers, grease gun, socket/breaker bar hammer, screwdriver and brush. Begin by spinning each wheel to check for noise, rolling resistance and endplay. If any detectable movement occurs when moving the wheel in and out on the spindle is observed then the bearings should be inspected and either packed with grease or replaced as necessary. Take out disc brake caliper and caliper mounting bracket after removing wheel. On ABS equipped vehicles remove front wheel speed sensors while in case of 4WD models remove free running hub if present. In case of 2WD Frontier models remove hub cap followed by cotter pin spindle nut as well as thrust washer. On 4WD frontier models also all Xterras and pathfinders remove lockwasher screws lockwasher along with locknut using a special tool then pull hub assembly off spindle. Pry rear seal from hub assembly, remove inner wheel bearing and clean out all old grease from bearings, hub, spindle using solvent. Examine races and bearings for damage; replace them as matched sets if necessary. Pack bearings with high temperature front wheel bearing grease; apply grease to the spindle and hub races. Put together again the hub assembly while for 2WD Frontier models follow specific procedures for tightening of spindle nut torque as follows; tighten the locknut to specified torques for 4WD Frontier models plus all Xterras & Pathfinders measuring wheel bearing preload adjust respectively according to need). Finish installments by performing reverse steps while ensuring proper torque of lugs nuts on wheels plus attachment of hub cap in place.