How to remove and install the axle shaft on the Nissan Versa?

To remove the axle shaft, first loosen the front wheel lug nuts, raise the vehicle, and support it securely on jackstands before removing the wheel. Next, take out the cotter pin and the axle shaft/hub nut, using a prybar between two wheel studs to assist in loosening it. Alternatively, the vehicle can remain on the ground while the hubcap or center cap is removed, followed by the cotter pin and loosening the axle shaft/hub nut. Then, detach the wheel speed sensor from the steering knuckle. For 2011 and earlier models, remove the control arm ball joint-to-steering knuckle pinch bolt, pry downward on the lower control arm to separate the lower balljoint from the steering knuckle, and push the axle shaft out of the hub while pulling outward on the steering knuckle and hub assembly. If the axle shaft splines are frozen, tap the end of the axle shaft with a soft-faced hammer or use a puller. Place a drain pan underneath the transaxle to catch any lubricant that may spill out during removal. For the left axle shaft, carefully pry the inner CV joint out of the transaxle. For the right axle shaft, detach it from the support bracket by removing the retainer-to-bracket bolts and marking the relationship of the bearing to the support bracket before pulling out the assembly. For 2012 and later models, disconnect the brake hose bracket from the strut, remove the brake caliper and disc without disconnecting the brake hose, and suspend the caliper to prevent damage. Break free the axle shaft from the hub, remove the strut-to-steering knuckle fasteners, and push the axle shaft out of the hub while pulling outward on the steering knuckle and hub assembly. Use a prybar or slide hammer with an axle shaft removal tool to remove the inner CV joint from the transaxle. Install a new axle shaft oil seal on the transaxle case if necessary. For installation, place a new retaining clip on the axle end before installation if reusing the old axle, and follow the reverse order of removal while ensuring to push the left axle shaft in sharply to seat the retaining ring. Tighten all fasteners to the proper torque specifications, ensuring the brake caliper mounting bolts are also tightened on 2012 and later models. Finally, install a new cotter pin, the wheel and lug nuts, lower the vehicle, tighten the lug nuts, and check the transaxle lubricant level, adding if necessary.

Genuine Nissan Versa Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

33 Axle Shafts found

View related parts
Nissan Versa Front Drive Shaft Assembly Right Hand
Part Number: 39100-3HC0A
$365.50 MSRP: $557.85
You Save: $192.35 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH; Axle Assembly
- Position: Passenger Side
- Replaces: 39100-9KH0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Shaft Assembly Left Hand
Part Number: 39101-EM40C
$359.36 MSRP: $494.98
You Save: $135.62 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH. This item is non-returnable.; Axle Assembly
- Position: Driver Side
- Replaces: 39101-9EG0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2012 Nissan Versa | SL | 4 Cyl 1.8L | MR18DE
View related parts
Nissan Versa Front Drive Shaft Assembly Left Hand
Part Number: 39101-3HC0A
$377.79 MSRP: $576.60
You Save: $198.81 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH; Axle Assembly
- Position: Driver Side
- Replaces: 39101-9KH0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Shaft Assembly Right Hand
Part Number: 39100-3AB0C
$352.19 MSRP: $537.53
You Save: $185.34 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH
- Manufacturer Note: PARALLEL 9KF0A CVT
- Position: Passenger Side
- Replaced by: 39100-9EK0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | Base, SL, SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Shaft Assembly Left Hand
Part Number: 39101-9EK0B
$273.08 MSRP: $416.80
You Save: $143.72 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH
- Manufacturer Note: CVT
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2019 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Shaft Assembly Left Hand
Part Number: 39101-5RD1A
$395.38 MSRP: $603.45
You Save: $208.07 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH; Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2025 Nissan Versa | S, SR, SV | 4 Cyl 1.6 L GAS
View related parts
Nissan Versa Front Drive Shaft Assembly Right Hand
Part Number: 39100-5RD1A
$453.11 MSRP: $691.57
You Save: $238.46 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH; Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2025 Nissan Versa | S, SR, SV | 4 Cyl 1.6 L GAS
View related parts
Nissan Versa Front Drive Shaft Assembly Left Hand
Part Number: 39101-3AB0C
$386.91 MSRP: $590.52
You Save: $203.61 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH; Axle Assembly
- Manufacturer Note: PARALLEL 9KF0A CVT
- Position: Driver Side
- Replaces: 39101-9KF0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | Base, SL, SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Shaft Assembly Left Hand
Part Number: 39101-3HC0B
$380.19 MSRP: $580.27
You Save: $200.08 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH; Axle Assembly
- Position: Driver Side
- Replaces: 39101-9KH0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Shaft Assembly Right Hand
Part Number: 39100-9EK0A
$352.19 MSRP: $537.53
You Save: $185.34 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH; Axle Assembly
- Manufacturer Note: CVT
- Position: Passenger Side
- Replaces: 39100-3AB0C, 39100-3AW0C, 39100-9KF0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | Base, SL, SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Shaft Assembly Right Hand
Part Number: 39100-EL005
$359.58 MSRP: $548.82
You Save: $189.24 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH
- Position: Passenger Side
- Replaced by: 39100-9EM0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2012 Nissan Versa | S, SL | 4 Cyl 1.8L | MR18DE
View related parts
Nissan Versa Front Drive Shaft Assembly Right Hand
Part Number: 39100-3HC0B
$374.11 MSRP: $570.98
You Save: $196.87 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH; Axle Assembly
- Position: Passenger Side
- Replaces: 39100-9KH0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Shaft Assembly Left Hand
Part Number: 39101-9EK0A
$351.17 MSRP: $535.98
You Save: $184.81 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH
- Manufacturer Note: CVT
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2019 Nissan Versa | Base, SL, SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Shaft Assembly Left Hand
Part Number: 39101-EL005
$362.02 MSRP: $552.53
You Save: $190.51 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH
- Manufacturer Note: GKN
- Position: Driver side
- Replaced by: 39101-9EM0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2012 Nissan Versa | S, SL | 4 Cyl 1.8L | MR18DE
View related parts
Nissan Versa Front Drive Shaft Assembly Right Hand
Part Number: 39100-5RA1A
$429.87 MSRP: $656.08
You Save: $226.21 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH; Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2025 Nissan Versa | S, SR, SV | 4 Cyl 1.6 L GAS
View related parts
Nissan Versa Front Drive Shaft Assembly Right Hand
Part Number: 39100-9EK0B
$284.15 MSRP: $433.68
You Save: $149.53 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH
- Manufacturer Note: CVT
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2019 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Shaft Assembly Left Hand
Part Number: 39101-5RA1A
$294.12 MSRP: $448.90
You Save: $154.78 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,LH; Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2025 Nissan Versa | S, SR, SV | 4 Cyl 1.6 L GAS
View related parts
Nissan Versa Front Drive Right Hand Shaft Assembly
Part Number: 39100-1HM0B
$568.63 MSRP: $867.87
You Save: $299.24 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2014 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Right Hand Shaft Assembly
Part Number: 39100-3AW0C
$352.19 MSRP: $537.53
You Save: $185.34 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH
- Position: Passenger Side
- Replaced by: 39100-9EK0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2013-2014 Nissan Versa | Base, SL, SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Front Drive Right Hand Shaft Assembly
Part Number: 39100-9KH0A
$365.50 MSRP: $557.85
You Save: $192.35 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assy-Front Drive,RH
- Position: Passenger Side
- Replaced by: 39100-3HC0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014-2016 Nissan Versa | SV | 4 Cyl 1.6L | HR16DE

| Page 1 of 2 |Next >

1-20 of 33 Results

Nissan Versa Axle Shaft

The Nissan Versa Axle Shaft is the component that sends power from the differential or transaxle to the drive wheels to provide power to the car. The Axle Shaft, which is a halfshaft with a splined end, attaches to the side gears of the differential or transaxle on the inner end and the wheel hub on the outer end, allowing each wheel to receive torque while turning in a corner. Within the Versa drivetrain, the Axle Shaft operates with constant velocity joints. The joints enable smooth rotation of the axle as the suspension moves up and down. As a result, power delivery and steering angles are supported without binding. In case the boots around those joints tear, there can be contamination, which can cause noise or vibration in a Nissan Versa that indicates wear in the Axle Shaft assembly. Nissan's design favors independent suspension, so each Versa wheel connects to its own Axle Shaft instead of a common solid axle. This aids the car's ride quality over uneven surfaces. Over time, a Nissan part's bearing surfaces, seals, and splines may deteriorate. Impact with curbs may bend the shaft, which would compromise alignment and lubrication.

If you need any OEM Nissan Versa Axle Shaft, feel free to choose them out of our huge selection of genuine Nissan Versa Axle Shaft. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Versa Axle Shaft Parts Questions & Experts Answers

Front Drive Shaft Assembly Right Hand
39100-EM40C
Q: How to remove and install the axle shaft on the Nissan Versa?
A:
To remove the axle shaft, first loosen the front wheel lug nuts, raise the vehicle, and support it securely on jackstands before removing the wheel. Next, take out the cotter pin and the axle shaft/hub nut, using a prybar between two wheel studs to assist in loosening it. Alternatively, the vehicle can remain on the ground while the hubcap or center cap is removed, followed by the cotter pin and loosening the axle shaft/hub nut. Then, detach the wheel speed sensor from the steering knuckle. For 2011 and earlier models, remove the control arm ball joint-to-steering knuckle pinch bolt, pry downward on the lower control arm to separate the lower balljoint from the steering knuckle, and push the axle shaft out of the hub while pulling outward on the steering knuckle and hub assembly. If the axle shaft splines are frozen, tap the end of the axle shaft with a soft-faced hammer or use a puller. Place a drain pan underneath the transaxle to catch any lubricant that may spill out during removal. For the left axle shaft, carefully pry the inner CV joint out of the transaxle. For the right axle shaft, detach it from the support bracket by removing the retainer-to-bracket bolts and marking the relationship of the bearing to the support bracket before pulling out the assembly. For 2012 and later models, disconnect the brake hose bracket from the strut, remove the brake caliper and disc without disconnecting the brake hose, and suspend the caliper to prevent damage. Break free the axle shaft from the hub, remove the strut-to-steering knuckle fasteners, and push the axle shaft out of the hub while pulling outward on the steering knuckle and hub assembly. Use a prybar or slide hammer with an axle shaft removal tool to remove the inner CV joint from the transaxle. Install a new axle shaft oil seal on the transaxle case if necessary. For installation, place a new retaining clip on the axle end before installation if reusing the old axle, and follow the reverse order of removal while ensuring to push the left axle shaft in sharply to seat the retaining ring. Tighten all fasteners to the proper torque specifications, ensuring the brake caliper mounting bolts are also tightened on 2012 and later models. Finally, install a new cotter pin, the wheel and lug nuts, lower the vehicle, tighten the lug nuts, and check the transaxle lubricant level, adding if necessary.

Related Nissan Versa Parts

Browse by Year

2025 Axle Shaft 2024 Axle Shaft 2023 Axle Shaft 2022 Axle Shaft 2021 Axle Shaft 2020 Axle Shaft 2019 Axle Shaft 2018 Axle Shaft 2017 Axle Shaft 2016 Axle Shaft 2015 Axle Shaft 2014 Axle Shaft 2013 Axle Shaft 2012 Axle Shaft 2011 Axle Shaft 2010 Axle Shaft 2009 Axle Shaft 2008 Axle Shaft 2007 Axle Shaft