×
- Hello
- Login or Register
- Quick Links
- Live Chat
- Track Order
- Parts Availability
- RMA
- Help Center
- Contact Us
- Shop for
- Nissan Parts
- Nissan Accessories
My Garage
My Account
Cart
Genuine Nissan Xterra Distributor Cap
Ignition Distributor Cap- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
4 Distributor Caps found
Nissan Xterra Cap Assy-Distributor
Part Number: 22162-7B000$47.92 MSRP: $62.92You Save: $15.00 (24%)Ships in 1-3 Business Days
Nissan Xterra Cap Assy-Distributor
Part Number: 22162-3S500$18.22 MSRP: $23.92You Save: $5.70 (24%)Ships in 1-3 Business Days
Nissan Xterra Cap Assy-Distributor
Part Number: 22162-1S700$18.22 MSRP: $23.92You Save: $5.70 (24%)Ships in 1-3 Business Days
Nissan Xterra Distributor Cap
Distributor Cap for Nissan Xterra efficiently routes high-voltage electricity from the ignition coil to spark plug wires in proper firing order. This allows your engine to ignite your fuel to run. The rotor is shielded by a plastic-covered housing. This housing protects the Distributor Cap's internal parts. The rotor spins with the camshaft. At this moment, it sweeps past posts matched to each cylinder. The posts pass current to the cylinder precisely at the moment of combustion. Theft can be prevented by the Distributor Cap as the Nissan Xterra Distributor Cap will shut down the engine. The use of an O-ring or gasket creates a tight seal that prevents moisture from entering the system that can short it and stop the engine. Heat, vibration, carbon buildup, or terminal erosion can all degrade the component. In cold climates, cracking may occur due to temperature shifts stressing the plastic. Clean the Distributor Cap on the Nissan Xterra to limit carbon deposits. When the Distributor Cap wears out or fails, your vehicle may start to shake and idle roughly, stall, backfire, make squealing noises while running, and be hard to turn over. When you replace it at the right time, you help your Nissan Xterra deliver optimum performance.
If you need any OEM Nissan Xterra Distributor Cap, feel free to choose them out of our huge selection of genuine Nissan Xterra Distributor Cap. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.
Nissan Xterra Distributor Cap Parts Questions & Experts Answers
- Q: How to check and replace Distributor Rotor,spark plug wires and distributor cap on Nissan Xterra?A:This process is only suitable for four-cylinder and 3.3L V6 engines. Start by visually inspecting spark plug wires while the engine is running inside a well-ventilated, dark garage. Put up each wire to see if any flashing or sparks happen on damaged sections. If any flash occurs, write down that you should buy new wires and look at the distributor cap and rotor after the engine cools down. So as not to mix up their order, inspect each spark plug wire individually and number them appropriately. Twist and pull rubber boot to remove wire from spark plug. Check inside boot for corrosion and make sure that when pushing the wire and boot back onto the plug it fits snugly. Clean with a piece of cloth, looking whether there are any burns, cracks or other damages on the cable. Pull off rubber boot only when disconnecting a wire from the distributor; also check its fit as well as corrosion presence. Make sure also that other spark plug wires are secured at both ends before moving to inspect them further by checking if they are connected tightly at distributor and at spark plugs respectively. Where new wires are required, purchase an appropriate set for your engine model only, changing them one after another in order not to mess up with firing order. While detaching distributor cap find out if it has any cracks, carbon tracks or worn out or loose contacts. Look also at rotor for cracks as well as carbon tracks.The cap including its rotor should be replaced immediately incase of any damage or imperfections being observed on such components.If new spark plugs are installed then it is advisable to put in place a new cap plus rotor.However,in case you still want to use the old unit,you have to measure resistance between the contacts of wires using an ohmmeter (multimeter),and between the contacts of these cables with respect to ground across the housing plate of cap.If in this case,the resistance is in excess of the maximum specified,then the wires or cap has to be replaced. Therefore, when replacing a cap, start by moving only one wire at a time from the old cap to the corresponding place on the new one in order to avoid any firing order errors.
