How to remove and install the door handle, door latch assembly, and door lock cylinder on a Nissan Xterra?

Take out the door trim panel and the plastic water-shield. Remove the latch retaining screws from the end of the door, then reach inside the door to release the latch from the control rods. Certain models have a stiffening brace that must be removed to gain access to the rear of the latch. For any vehicle with power door locks, unplug its electrical connector. Unhook the door latch, and if it exists, unfasten the door lock solenoid. Installation will be done in reverse from removal. If present, separate electrical contact from locking cylinder. A screwdriver or pliers can be used to take off this part's locking cylinder retaining clip. Move lock outward so that it separates itself from door and lock cylinder control rod. In some cases, one has to disentangle a clip which attaches control rod and lock cylinder together. Take off control link rod connected to outer handle then remove outer handle retaining nuts and pull handle away from door. For front doors, holes in door frame provide access for removing outside handle retaining nuts. On vehicles with rear doors, pry out trim caps so as to get at exterior handle retention nuts.Installation is accomplished by reversing above removal procedures.Pull off the plate concealing control rod guide.Release retaining screws, pulling handle free of hinge then unfastening control rods from behind inside handles.Pull back on screw retainer cover.If available at all,the inside handle retaining screw should be detached such that it slides back into place away from its attachment point on a nearby wall.Installation is carried out in reverse order as compared to removal process.

Genuine Nissan Xterra Door Lock Cylinder

Door Lock Cylinder Tumbler

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Door Lock Cylinders found

View related parts
Nissan Xterra Cylinder Set-Door Lock,L
Part Number: H0601-EA025
$54.99 MSRP: $82.69
You Save: $27.70 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Set-Door Lock,LH; Cylinder & Keys, Lock Cylinder
- Position: Driver Side
- Replaces: H0601-EA000, H0601-EA027
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2012 Nissan Xterra | Base Camp, Off-Road, PRO-4X, S, SE, X | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Cylinder Set - Door Lock, LH
Part Number: H0601-1PA0A
$59.69 MSRP: $83.11
You Save: $23.42 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Set-Door Lock,LH; Cylinder & Keys, Lock Cylinder
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2015 Nissan Xterra | Base Camp, Off-Road, PRO-4X, S, X | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Cylinder Assy-Door Lock
Part Number: H0600-3J185
$90.26 MSRP: $139.07
You Save: $48.81 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Set-Door Lock,LH; Cylinder & Keys, Lock Cylinder
- Position: Driver side
- Replaces: 80600-3S500, 80600-0W000, 80601-3J100, 80601-3S500, H0600-3J125, H0600-9E000, H0600-3S500, H0601-3J100, H0600-3J100, H0601-3S500
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E, VG33ER
View related parts
Nissan Xterra Back Door Lock Cylinder
Part Number: K0600-7Z025
$26.39 MSRP: $39.69
You Save: $13.30 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Set-Back Door Lock; Cylinder & Keys, Lock Cylinder
- Replaces: K0600-7Z000, 90600-7Z000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E, VG33ER
View related parts
Nissan Xterra Cylinder Set-Door Lock,R
Part Number: H0600-EA000
$50.91 MSRP: $76.56
You Save: $25.65 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Set-Door Lock,RH; Cylinder & Keys, Lock Cylinder
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2009 Nissan Xterra | Base Camp, Off-Road, S, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Cylinder Set-Door Lock,LH
Part Number: 80601-EA000
$58.55 MSRP: $88.05
You Save: $29.50 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder & Keys, Lock Cylinder
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2009 Nissan Xterra | Base Camp, Off-Road, S, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Back Door Lock Cylinder Set
Part Number: 90600-EA000
$73.46 MSRP: $103.75
You Save: $30.29 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Set-Back Door Lock; Lock Cylinder
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2010-2012 Nissan Xterra | Off-Road, PRO-4X, S | 6 Cyl 4.0L | VQ40DE
- 2005-2008 Nissan Xterra | Base Camp, S | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Cylinder Assy-Door Lock
Part Number: H0600-3S500
$90.26 MSRP: $139.07
You Save: $48.81 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: RH & LH
- Replaced by: H0600-3J185
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2001 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Xterra Back Door Lock Cylinder Set
Part Number: 90600-7Z000
$26.39 MSRP: $39.69
You Save: $13.30 (34%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Set-Back Door Lock; Lock Cylinder
- Replaced by: K0600-7Z025
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2003 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E, VG33ER
View related parts
Nissan Xterra Cylinder-Door Lock
Part Number: 80600-0W000
$90.26 MSRP: $139.07
You Save: $48.81 (36%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy-Door Lock
- Replaced by: H0600-3J185
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2002 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Xterra Cylinder Set - Door Lock, L
Part Number: H0601-EA000
$54.99 MSRP: $82.69
You Save: $27.70 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Set-Door Lock,LH
- Position: Driver side
- Replaced by: H0601-EA025
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2008 Nissan Xterra | Base Camp, S | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Steering Lock Set
Part Number: D8700-EA010
$249.23 MSRP: $352.02
You Save: $102.79 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Set-Steering; Cylinder & Keys, Ignition Lock Cylinder
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2015 Nissan Xterra | Base Camp, Off-Road, PRO-4X, S, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Door Lock Cylinder Set
Part Number: 80601-3J100
$90.26 MSRP: $139.07
You Save: $48.81 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Set-Door Lock,LH
- Position: Driver side
- Replaced by: H0600-3J185
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2002 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Xterra Door Lock Cylinder Set
Part Number: H0601-3S500
$90.26 MSRP: $139.07
You Save: $48.81 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Set-Door Lock,LH
- Manufacturer Note: LH ONLY
- Position: Driver side
- Replaced by: H0600-3J185
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2001 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Xterra Cylinder Set-Door Lock,LH
Part Number: 80601-3S500
$90.26 MSRP: $139.07
You Save: $48.81 (36%)
ADD TO CART
Product Specifications
- Position: Driver side
- Replaced by: H0600-3J185
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2001 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Xterra Door Lock Cylinder Set Right Hand
Part Number: 80600-3S500
$90.26 MSRP: $139.07
You Save: $48.81 (36%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy-Door Lock
- Replaced by: H0600-3J185
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2002 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Xterra Back Door Lock Cylinder
Part Number: K0600-7Z000
$26.39 MSRP: $39.69
You Save: $13.30 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Set-Back Door Lock
- Replaced by: K0600-7Z025
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2001 Nissan Xterra | SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E

Nissan Xterra Door Lock Cylinder

The Nissan Xterra Door Lock Cylinder makes the front door lock and unlock by linking the action of the key to the internal latch with a passive connection. The Door Lock Cylinder at each front door of the Xterra is the place housing the key entry slot and that engages with the locking hardware on the vehicle. This allows cab occupants to lock or unlock the cab by simply turning it. When the correct key is inserted, small internal tumblers line up, allowing the cylinder to turn and retract or extend the lock linkage. Wear and tear is commonly due to everyday usage, which may make the Door Lock Cylinder stiff in operation, may make the key difficult to turn, and may trap the key in the slot. No alternate versions are identified. Thus, the Door Lock Cylinder for this Nissan comes in one standard format. The Door Lock Cylinder, if in good working condition, will help keep the Nissan doors locked up, allow easy access to the Xterra cabin, and keep the Nissan Xterra usable on a daily basis.

If you need any OEM Nissan Xterra Door Lock Cylinder, feel free to choose them out of our huge selection of genuine Nissan Xterra Door Lock Cylinder. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Xterra Door Lock Cylinder Parts Questions & Experts Answers

Back Door Lock Cylinder
K0600-7Z025
Q: How to remove and install the door handle, door latch assembly, and door lock cylinder on a Nissan Xterra?
A:
Take out the door trim panel and the plastic water-shield. Remove the latch retaining screws from the end of the door, then reach inside the door to release the latch from the control rods. Certain models have a stiffening brace that must be removed to gain access to the rear of the latch. For any vehicle with power door locks, unplug its electrical connector. Unhook the door latch, and if it exists, unfasten the door lock solenoid. Installation will be done in reverse from removal. If present, separate electrical contact from locking cylinder. A screwdriver or pliers can be used to take off this part's locking cylinder retaining clip. Move lock outward so that it separates itself from door and lock cylinder control rod. In some cases, one has to disentangle a clip which attaches control rod and lock cylinder together. Take off control link rod connected to outer handle then remove outer handle retaining nuts and pull handle away from door. For front doors, holes in door frame provide access for removing outside handle retaining nuts. On vehicles with rear doors, pry out trim caps so as to get at exterior handle retention nuts.Installation is accomplished by reversing above removal procedures.Pull off the plate concealing control rod guide.Release retaining screws, pulling handle free of hinge then unfastening control rods from behind inside handles.Pull back on screw retainer cover.If available at all,the inside handle retaining screw should be detached such that it slides back into place away from its attachment point on a nearby wall.Installation is carried out in reverse order as compared to removal process.

Related Nissan Xterra Parts

Browse by Year

2015 Door Lock Cylinder 2014 Door Lock Cylinder 2013 Door Lock Cylinder 2012 Door Lock Cylinder 2011 Door Lock Cylinder 2010 Door Lock Cylinder 2009 Door Lock Cylinder 2008 Door Lock Cylinder 2007 Door Lock Cylinder 2006 Door Lock Cylinder 2005 Door Lock Cylinder 2004 Door Lock Cylinder 2003 Door Lock Cylinder 2002 Door Lock Cylinder 2001 Door Lock Cylinder 2000 Door Lock Cylinder