How to check and repack the front wheel hub and wheel bearings on Nissan Frontier?

The front wheel bearings must be checked and repacked. For this, you need to have jackstands that can support the vehicle safely, torque wrench, grease hammer, wood block, needle nose pliers, grease gun, socket/breaker bar hammer, screwdriver and brush. Begin by spinning each wheel to check for noise, rolling resistance and endplay. If any detectable movement occurs when moving the wheel in and out on the spindle is observed then the bearings should be inspected and either packed with grease or replaced as necessary. Take out disc brake caliper and caliper mounting bracket after removing wheel. On ABS equipped vehicles remove front wheel speed sensors while in case of 4WD models remove free running hub if present. In case of 2WD Frontier models remove hub cap followed by cotter pin spindle nut as well as thrust washer. On 4WD frontier models also all Xterras and pathfinders remove lockwasher screws lockwasher along with locknut using a special tool then pull hub assembly off spindle. Pry rear seal from hub assembly, remove inner wheel bearing and clean out all old grease from bearings, hub, spindle using solvent. Examine races and bearings for damage; replace them as matched sets if necessary. Pack bearings with high temperature front wheel bearing grease; apply grease to the spindle and hub races. Put together again the hub assembly while for 2WD Frontier models follow specific procedures for tightening of spindle nut torque as follows; tighten the locknut to specified torques for 4WD Frontier models plus all Xterras & Pathfinders measuring wheel bearing preload adjust respectively according to need). Finish installments by performing reverse steps while ensuring proper torque of lugs nuts on wheels plus attachment of hub cap in place.

Genuine Nissan Frontier Wheel Hub

Wheel Axle Hub

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Wheel Hubs found

View related parts
Nissan Frontier Hub Assembly Road Wheel
Part Number: 40202-4X01A
$233.15 MSRP: $339.87
You Save: $106.72 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Replaced by: 40202-9BT1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2010-2019 Nissan Frontier | LE, Off-Road, PRO-4X, S, SE, SL, SV | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Hub Assembly Road Wheel
Part Number: 40202-4X00A
$262.74 MSRP: $401.00
You Save: $138.26 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Replaced by: 40202-9BT0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2010-2019 Nissan Frontier | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Road Wheel Hub Assembly Front
Part Number: 40202-EA300
$233.15 MSRP: $339.87
You Save: $106.72 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Position: Front
- Replaced by: 40202-9BT1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2008 Nissan Frontier | LE, Off-Road, SE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Road Wheel Hub Assembly Front
Part Number: 40202-ZP90A
$233.15 MSRP: $339.87
You Save: $106.72 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Position: Front
- Replaced by: 40202-9BT1A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2011 Nissan Frontier | LE, Off-Road, SE, SL, SV | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Road Wheel Hub Assembly Front
Part Number: 40202-EA000
$262.74 MSRP: $401.00
You Save: $138.26 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Position: Front
- Replaced by: 40202-9BT0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2008 Nissan Frontier | LE, Off-Road, SE, XE | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Hub Assembly Road Wheel
Part Number: 40202-9BS0A
$262.74 MSRP: $401.00
You Save: $138.26 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 40202-9BT0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2018-2019 Nissan Frontier | S, SL, SV | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Road Wheel Hub Assembly Front
Part Number: 40202-9BT1A
$233.15 MSRP: $339.87
You Save: $106.72 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front; Front Hub, Front Hub & Bearing, Hub Assembly
- Position: Front
- Replaces: 40202-EA300, 40202-4X01A, 40202-ZP90A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2025 Nissan Frontier | Desert Runner, Hardbody Edition, LE, Nismo Off-Road, PRO-4X, PRO-X, S, SE, SL, SV, XE | 4 Cyl 2.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS
View related parts
Nissan Frontier HUB ASSY-ROAD WHEEL,FRONT
Part Number: 40202-9BT0B
$262.74 MSRP: $401.00
You Save: $138.26 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Hub, Front Hub & Bearing, Hub Assembly
- Position: Front
- Replaces: 40202-9BS0A, 40202-EA000, 40202-4X00A, 40202-9BT0A, 40202-ZP50A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2025 Nissan Frontier | Desert Runner, Hardbody Edition, LE, Nismo Off-Road, PRO-4X, PRO-X, S, SE, SL, SV, XE | 4 Cyl 2.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS
View related parts
Nissan Frontier Road Wheel Hub Assembly Front
Part Number: 40202-ZP50A
$262.74 MSRP: $401.00
You Save: $138.26 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Position: Front
- Replaced by: 40202-9BT0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2011 Nissan Frontier | LE, Off-Road, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 4.0L | QR25DE, VQ40DE
View related parts
Nissan Frontier Hub Assembly Road Wheel
Part Number: 40202-7Z600
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front; Front Hub, Hub
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Frontier | SC, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Hub Assembly Road Wheel
Part Number: 40202-9Z400
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front; Front Hub, Hub
- Replaces: 40202-3S615
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2004 Nissan Frontier | SE, STD, XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Frontier Hub Assembly Road Wheel
Part Number: 40202-3S615
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Replaced by: 40202-9Z400
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2003 Nissan Frontier | SE, STD, XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Frontier Hub Assembly Road Wheel
Part Number: 40202-7Z700
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front; Front Hub, Hub
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Frontier | SC, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Hub Assy-Free Running
Part Number: 40250-8B400
Product Specifications
- Other Name: Hub Assembly, Hub Cover, Locking Hub
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2001 Nissan Frontier | XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Frontier Hub Assembly Road Wheel
Part Number: 40202-7Z200
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front; Front Hub, Hub
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1999-2001 Nissan Frontier | SC, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Hub Assembly
Part Number: 40202-2S605
Product Specifications
- Other Name: Hub Assembly-Road Wheel,Front
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2001 Nissan Frontier | SC, SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E
View related parts
Nissan Frontier Hub Assembly, Free Running
Part Number: 40260-8B400
Product Specifications
- Other Name: Hub Assy-Free Running; Hub Assembly, Hub Cover, Locking Hub
- Manufacturer Note: F/FREE RUNNING HUB-AUTO
- Replaces: 40260-9Z500
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2004 Nissan Frontier | SC, SE, XE | 4 Cyl 2.4L, 6 Cyl 3.3L | KA24DE, VG33E

Nissan Frontier Wheel Hub

The Nissan Frontier Wheel Hub attaches each wheel to the vehicle while allowing them to turn for safe steering and braking. The Wheel Hub, positioned between the drive axle and the brake drum or disc, contains wheel bearings and mounting studs and, in many cases, sensors and brake parts in a robust bolted housing. Bearings that are either roller or tapered reduce friction, whereas splined teeth on drive applications transfer power from axle to wheels. There are three types of configuration discussed below. A sealed unit or integral Wheel Hub that may carry an ABS sensor is replaced whole. A unit that may be pressed apart from the steering knuckle and a non-driven axle version with opposed replaceable tapered roller bearings. No matter the type, proper bolt torque secures the wheel and helps with both performance and safety on every Nissan Frontier. The original specification of axle-extension width, flange range, and bolt pattern should be matched when selecting a Wheel Hub for Nissan Frontier. A well-crafted Wheel Hub ensures each Nissan Frontier's wheel movements are always smooth and tight.

If you need any OEM Nissan Frontier Wheel Hub, feel free to choose them out of our huge selection of genuine Nissan Frontier Wheel Hub. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Frontier Wheel Hub Parts Questions & Experts Answers

Hub Assembly
40202-2S605
Q: How to check and repack the front wheel hub and wheel bearings on Nissan Frontier?
A:
The front wheel bearings must be checked and repacked. For this, you need to have jackstands that can support the vehicle safely, torque wrench, grease hammer, wood block, needle nose pliers, grease gun, socket/breaker bar hammer, screwdriver and brush. Begin by spinning each wheel to check for noise, rolling resistance and endplay. If any detectable movement occurs when moving the wheel in and out on the spindle is observed then the bearings should be inspected and either packed with grease or replaced as necessary. Take out disc brake caliper and caliper mounting bracket after removing wheel. On ABS equipped vehicles remove front wheel speed sensors while in case of 4WD models remove free running hub if present. In case of 2WD Frontier models remove hub cap followed by cotter pin spindle nut as well as thrust washer. On 4WD frontier models also all Xterras and pathfinders remove lockwasher screws lockwasher along with locknut using a special tool then pull hub assembly off spindle. Pry rear seal from hub assembly, remove inner wheel bearing and clean out all old grease from bearings, hub, spindle using solvent. Examine races and bearings for damage; replace them as matched sets if necessary. Pack bearings with high temperature front wheel bearing grease; apply grease to the spindle and hub races. Put together again the hub assembly while for 2WD Frontier models follow specific procedures for tightening of spindle nut torque as follows; tighten the locknut to specified torques for 4WD Frontier models plus all Xterras & Pathfinders measuring wheel bearing preload adjust respectively according to need). Finish installments by performing reverse steps while ensuring proper torque of lugs nuts on wheels plus attachment of hub cap in place.