How to remove the camshaft, camshaft seal, and lash adjuster on the 3.3L V6 Nissan Pathfinder?

To take out the Lash Adjusters, begin by removing the valve cover and rocker arm shaft assemblies. Use rubber bands to keep them in place so that they don't come off from their guides. The Lash Adjuster guide assembly is then removed and Lash Adjusters are taken out of the bores one at a time, keeping them in order. They should not be laid on their side or upside down to avoid trapping air inside. If you feel like there is trapped air, put back the rocker arms, shafts as well as, valve covers and run the engine for 10 minutes at 1000 rpm to bleed the air out of the Lash Adjusters. While they are outside of the engine, check for wear by examining them again so that you can replace if needed. To get rid of camshafts remove heads and pry camshaft cover plate gently from there (Gillespie 7). When unscrewing retaining bolt hold it with holding lugs tightening it accordingly till you remove thrust plate and bolt. The camshaft oil seal should be removed with caution to prevent scuffing or scratching it as it is being pulled out. By rotating in twist squeeze motion pull oronsealpacificcamshaft out of cylinder head (Olay/Weisman Architects). Camshafts are lubricated on bearing journals and lobes using moly-based engine assembly lube before they are cautiously placed into position in the cylinder head (Olay/Weisman Architects). Install camshaft thrust plates with their retaining bolts and ensure that I have checked if my camshafts have any end play (Olay/Weisman Architects). In case endplay does not fall within certain range then thrust plate has to be replaced (Olay/Weisman Architects). Set up camshaft oil seal thus finishing assembling cylinder head.

Genuine Nissan Pathfinder Camshaft Seal

Cam Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Camshaft Seals found

View related parts
Nissan Pathfinder Seal-Oil,Camshaft
Part Number: 13042-3HD0A
$10.61 MSRP: $15.37
You Save: $4.76 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Seal
- Manufacturer Note: ALTERNATIVE: 13042-3
- Replaces: 13042-6N200, 13042-3HD0B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2022-2025 Nissan Pathfinder | Platinum, Rock Creek, S, SL, SV | 6 Cyl 3.5 L GAS
- 2007-2019 Nissan Pathfinder | LE, Platinum, S, SE, SL, SV | 4 Cyl 2.5L, 6 Cyl 3.5L, 8 Cyl 5.6L | QR25DER, VK56DE, VQ35DD, VQ35DE
View related parts
Nissan Pathfinder Seal-Oil,Camshaft
Part Number: 13042-6N200
$10.61 MSRP: $15.37
You Save: $4.76 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 13042-3HD0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2012 Nissan Pathfinder | LE, SE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Pathfinder Seal-Oil CRANKSHAFT
Part Number: 13510-V5000
$7.53 MSRP: $10.38
You Save: $2.85 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal-Oil,Crankshaft Front
- Replaced by: 13510-88G00
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1987-1994 Nissan Pathfinder | SE, ST, XE | 6 Cyl 3.0L | VG30E, VG30I
View related parts
Nissan Pathfinder Seal Oil CAMSHAFT
Part Number: 13042-D0100
$11.79 MSRP: $16.25
You Save: $4.46 (28%)
ADD TO CART
Product Specifications
- Other Name: Seal-Oil,Camshaft
- Replaced by: 13042-0B001
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1987-2001 Nissan Pathfinder | LE, SE, ST, XE | 6 Cyl 3.0L, 6 Cyl 3.3L | VG30E, VG30I, VG33E
View related parts
Nissan Pathfinder Seal-Oil CRANKSHAFT Front
Part Number: 13042-D0101
$7.05 MSRP: $12.25
You Save: $5.20 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal-Oil,Camshaft
- Position: Front
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2003 Nissan Pathfinder | XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Pathfinder Oil Seal
Part Number: 13510-10Y00
$12.40 MSRP: $17.52
You Save: $5.12 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal-Oil,Crankshaft Front
- Replaced by: 13510-10Y12
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1996-2003 Nissan Pathfinder | LE, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Pathfinder Seal-Oil,Crankshaft Front
Part Number: 13510-V7201
$12.40 MSRP: $17.52
You Save: $5.12 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Position: Front
- Replaced by: 13510-10Y12
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2002 Nissan Pathfinder | XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Pathfinder Seal Oil CRANKSHAFT
Part Number: 13510-88G10
$7.53 MSRP: $10.38
You Save: $2.85 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal-Oil,Crankshaft Front
- Replaced by: 13510-88G00
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1993-1995 Nissan Pathfinder | SE, ST, XE | 6 Cyl 3.0L | VG30E
View related parts
Nissan Pathfinder Seal-Oil,Camshaft
Part Number: 13042-3HD0B
$10.61 MSRP: $15.37
You Save: $4.76 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 13042-3HD0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2018-2019 Nissan Pathfinder | Platinum, S, SL, SV | 6 Cyl 3.5L | VQ35DD

Nissan Pathfinder Camshaft Seal

The Nissan Pathfinder Camshaft Seal is located at the opening of your camshaft where it exits the cylinder head. This prevents any oil or dirt from damaging or contaminating the lubrication that runs out from there. The Camshaft Seal seals off the gap between the camshaft and the engine block. It keeps vital oil around the turning camshaft and keeps trash out. It helps the engine run efficiently. Tight against the camshaft surface and surrounding head, the component is a circular ring with constant contact to prevent leaks during continuous rotation. When the Camshaft Seal ensures the camshaft area is oil-tight, friction is minimized, valve timing remains precise, and performance stays consistent. The Camshaft Seal is also able to ensure the cleanliness of the lubricated zone. The information available indicates a single overall design with no alternative styles specified for Pathfinder, so the described form closely resembles that of typical Nissan engines. The Camshaft Seal plays a significant role in the day-to-day operation of the Nissan Pathfinder.

If you need any OEM Nissan Pathfinder Camshaft Seal, feel free to choose them out of our huge selection of genuine Nissan Pathfinder Camshaft Seal. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Pathfinder Camshaft Seal Parts Questions & Experts Answers

Seal Oil CAMSHAFT
13042-D0100
Q: How to remove the camshaft, camshaft seal, and lash adjuster on the 3.3L V6 Nissan Pathfinder?
A:
To take out the Lash Adjusters, begin by removing the valve cover and rocker arm shaft assemblies. Use rubber bands to keep them in place so that they don't come off from their guides. The Lash Adjuster guide assembly is then removed and Lash Adjusters are taken out of the bores one at a time, keeping them in order. They should not be laid on their side or upside down to avoid trapping air inside. If you feel like there is trapped air, put back the rocker arms, shafts as well as, valve covers and run the engine for 10 minutes at 1000 rpm to bleed the air out of the Lash Adjusters. While they are outside of the engine, check for wear by examining them again so that you can replace if needed. To get rid of camshafts remove heads and pry camshaft cover plate gently from there (Gillespie 7). When unscrewing retaining bolt hold it with holding lugs tightening it accordingly till you remove thrust plate and bolt. The camshaft oil seal should be removed with caution to prevent scuffing or scratching it as it is being pulled out. By rotating in twist squeeze motion pull oronsealpacificcamshaft out of Cylinder Head (Olay/Weisman Architects). Camshafts are lubricated on bearing journals and lobes using moly-based engine assembly lube before they are cautiously placed into position in the cylinder head (Olay/Weisman Architects). Install camshaft thrust plates with their retaining bolts and ensure that I have checked if my camshafts have any end play (Olay/Weisman Architects). In case endplay does not fall within certain range then thrust plate has to be replaced (Olay/Weisman Architects). Set up camshaft oil seal thus finishing assembling cylinder head.