How to remove and install a Brake Caliper on a Nissan Quest?

Before pulling it back out, loosen the front wheel lug nuts but do not take them off yet, then safely raise the front end of the vehicle and support it with jack stands and, finally, take off the front wheels. Then unscrew the brake hose nipple fitting from the caliper and connect it to the brake hose using a short piece of rubber tube of adequate inner diameter for the banjo fitting to thread into to in order to avoid any contamination of brake fluid as well as to reduce the amount of brake fluid loss. Subsequent to that, likewise, take out the caliper mounting bolts and then take off the caliper from the steering knuckle.During installation make sure to change the sealing washers of the brake line fitting in front and at the back of the brake line fitting and tighten the caliper mounting bolts and the banjo bolt to the recommended torque setting. Last put brake fluid back into the brake reservoir, fit the wheels and nuts, also lower the vehicle then torque the wheel nuts up to the required number.

Genuine Nissan Quest Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Brake Calipers found

View related parts
Nissan Quest Rear Right Hand Caliper Assembly Without Pads Or Shims
Part Number: 44001-1AA0A
$367.37 MSRP: $558.45
You Save: $191.08 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Rear RH,W/O Pad & Shim; Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Rear Caliper Assembly Left Hand Without Pad & Shim
Part Number: 44011-AL500
$255.52 MSRP: $358.83
You Save: $103.31 (29%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Rear LH,W/O Pad & Shim
- Position: Driver side
- Replaced by: 44011-CN11A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2008 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Rear Caliper Assembly Left Hand Without Pad & Shim
Part Number: 44011-1AA0A
$367.37 MSRP: $558.45
You Save: $191.08 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Rear LH,W/O Pad & Shim; Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2011-2017 Nissan Quest | LE, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Front Caliper Assembly Left Hand Without Pads Or Shims
Part Number: 41011-CN91B
$305.80 MSRP: $464.48
You Save: $158.68 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Front LH,W/O Pad & Shim; Caliper
- Position: Driver Side
- Replaces: 41011-CK000, 41011-CN91A, 41011-ZF00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2017 Nissan Quest | Base, LE, S, SE, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest CALIPER Assembly-Front RH,W/O Pads Or SHIMS
Part Number: 41001-CN91B
$321.01 MSRP: $487.70
You Save: $166.69 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER Assembly-Front RH,W/O Pad & SHIM; Caliper
- Position: Passenger Side
- Replaces: 41001-CK000, 41001-ZF00A, 41001-CN91A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2017 Nissan Quest | Base, LE, S, SE, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Rear Caliper Assembly Left Hand Without Pad & Shim
Part Number: 44011-CN11A
$327.37 MSRP: $358.83
You Save: $31.46 (9%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Rear LH,W/O Pad & Shim. This item is non-returnable.; Caliper, Caliper Assembly
- Position: Driver side
- Replaces: 44011-AL500, 44011-CB10A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2010 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest CALIPER Assembly-Front RH, W/O Pads Or SHIMS
Part Number: 41001-ZF00A
$305.80 MSRP: $487.70
You Save: $181.90 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER Assembly-Front RH,W/O Pad & SHIM
- Position: Passenger Side
- Replaced by: 41001-CN91B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2007 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest CALIPER Assembly-Front RH,W/O Pads Or SHIMS
Part Number: 41001-CN91A
$305.80 MSRP: $487.70
You Save: $181.90 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER Assembly-Front RH,W/O Pad & SHIM
- Position: Passenger Side
- Replaced by: 41001-CN91B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2006-2008 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest CALIPER Assembly-Front RH,W/O Pads Or SHIMS
Part Number: 41001-CK000
$305.80 MSRP: $487.70
You Save: $181.90 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER Assembly-Front RH,W/O Pad & SHIM
- Position: Passenger Side
- Replaced by: 41001-CN91B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2006 Nissan Quest | S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest CALIPER Assembly-Front LH, W/O Pads Or SHIMS
Part Number: 41011-ZF00A
$305.80 MSRP: $464.48
You Save: $158.68 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Front LH,W/O Pad & Shim
- Position: Driver side
- Replaced by: 41011-CN91B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2007 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest CALIPER Assembly-Front LH, W/O Pads Or SHIMS
Part Number: 41011-CN91A
$305.80 MSRP: $464.48
You Save: $158.68 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Front LH,W/O Pad & Shim
- Position: Driver side
- Replaced by: 41011-CN91B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2006-2008 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Front Caliper Assembly Left Hand Without Pads Or Shims
Part Number: 41011-CK000
$305.80 MSRP: $464.48
You Save: $158.68 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Front LH,W/O Pad & Shim
- Position: Driver side
- Replaced by: 41011-CN91B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2006 Nissan Quest | S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest CALIPER-Brake LH
Part Number: 41011-1B000
$65.14 MSRP: $92.00
You Save: $26.86 (30%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Front LH,W/O Pad & Shim; Caliper
- Position: Driver side
- Replaced by: 41011-0B000RE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1999-2003 Nissan Quest | GXE, SE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Quest Front Caliper Assembly Left Hand Without Pads Or Shims
Part Number: 41011-0B000
$65.14 MSRP: $92.00
You Save: $26.86 (30%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assy-Front LH,W/O Pad & Shim
- Position: Driver side
- Replaced by: 41011-0B000RE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1993-1998 Nissan Quest | GXE, XE | 6 Cyl 3.0L | VG30E
View related parts
Nissan Quest Rear Right Hand Caliper Assembly Without Pads Or Shims
Part Number: 44001-AL500
Product Specifications
- Other Name: Caliper Assy-Rear RH,W/O Pad & Shim
- Position: Passenger Side
- Replaced by: 44001-CN11A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2008 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest CALIPER-Brake RH
Part Number: 41001-1B000
Product Specifications
- Other Name: CALIPER Assembly-Front RH,W/O Pad & SHIM; Caliper
- Position: Passenger Side
- Replaced by: 41001-0B000RE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1999-2003 Nissan Quest | GXE, SE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Quest CALIPER Assembly-Front RH,W/O Pads Or SHIMS
Part Number: 41001-0B000
Product Specifications
- Other Name: CALIPER Assembly-Front RH,W/O Pad & SHIM
- Position: Passenger Side
- Replaced by: 41001-0B000RE
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1993-1998 Nissan Quest | GXE, XE | 6 Cyl 3.0L | VG30E
View related parts
Nissan Quest A CALIPER RH 99
Part Number: 44001-CN12A
Product Specifications
- Other Name: Caliper Assy-Rear RH,W/O Pad & Shim
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2010 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Rear Brake Left Hand
Part Number: 44011-CN12A
Product Specifications
- Other Name: Caliper Assy-Rear LH,W/O Pad & Shim
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2010 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Quest Rear Right Hand Caliper Assembly Without Pads Or Shims
Part Number: 44001-CN11A
Product Specifications
- Other Name: Caliper Assy-Rear RH,W/O Pad & Shim; Caliper
- Position: Passenger Side
- Replaces: 44001-CB10A, 44001-AL500
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2010 Nissan Quest | Base, S, SE, SL | 6 Cyl 3.5L | VQ35DE

Nissan Quest Brake Caliper

Nissan Quest Brake Caliper converts hydraulic pressure from the master cylinder into mechanical force that clamps brake pads against the rotor and slows the vehicle. When brake fluid enters the cast iron body, steel or phenolic pistons move outward to create friction on the disc. A hose port and a bleeder screw to vent air are present on the unit. Nissan systems have two confirmed styles. Fixed versions bolt in place and squeeze from both sides with opposing pistons that apply equal pad pressure. Floating versions carry their piston or pistons on the inboard side. As these extend, the caliper slides on guide pins so the outboard pad also grips the rotor. A screw-type mechanism for parking is present in some rear units. When seals leak, pistons seize, or slide pins corrode, it can cause low pedals, brake pull, drag, or uneven wear. This Brake Caliper design supports stopping for Nissan Quest. A healthy Brake Caliper keeps stops straight, while a Brake Caliper issue can let the Quest exhibit problems. Regular inspection of the Brake Caliper on any Nissan Quest helps catch damage early.

If you need any OEM Nissan Quest Brake Caliper, feel free to choose them out of our huge selection of genuine Nissan Quest Brake Caliper. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Quest Brake Caliper Parts Questions & Experts Answers

CALIPER Assembly-Front RH,W/O Pads Or SHIMS
41001-0B000
Q: How to remove and install a Brake Caliper on a Nissan Quest?
A:
Before pulling it back out, loosen the front wheel lug nuts but do not take them off yet, then safely raise the front end of the vehicle and support it with jack stands and, finally, take off the front wheels. Then unscrew the brake hose nipple fitting from the caliper and connect it to the brake hose using a short piece of rubber tube of adequate inner diameter for the banjo fitting to thread into to in order to avoid any contamination of brake fluid as well as to reduce the amount of brake fluid loss. Subsequent to that, likewise, take out the caliper mounting bolts and then take off the caliper from the steering knuckle.During installation make sure to change the sealing washers of the Brake Line fitting in front and at the back of the brake line fitting and tighten the caliper mounting bolts and the banjo bolt to the recommended torque setting. Last put brake fluid back into the brake reservoir, fit the wheels and nuts, also lower the vehicle then torque the wheel nuts up to the required number.