How to replace the Hood Cable and Hood Latch on the Nissan Versa?

To replace the latch, first remove the radiator grille, then scribe a line around the latch for alignment, and take out the latch retaining bolts to remove the latch. Disconnect the hood release cable by prying out the cable retainer from the rear of the latch assembly and disengaging the cable. For installation, reverse the removal process, ensuring the latch is adjusted so the hood engages securely when closed and the hood bumpers are slightly compressed. To replace the cable, disconnect it from the latch assembly, remove the left inner fender well liner, detach the cable from the clips along its length, and take out the inside hood release handle to disconnect the cable. Pull the cable grommet into the passenger compartment and then pull the cable through the hole. For installation, reverse the removal process, making sure to push on the grommet with your fingers from the passenger compartment to seat it correctly in the firewall.

Genuine Nissan Versa Hood Cable

Hood Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Hood Cables found

View related parts
Nissan Versa Hood Lock Control Cable Assembly
Part Number: 65620-1HL0A
$14.48 MSRP: $21.78
You Save: $7.30 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly-Hood Lock Control; Release Cable
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Versa | Base, SL, SV | 4 Cyl 1.6L | HR16DE
View related parts
Nissan Versa Cable Hood Lock
Part Number: 65620-EL00A
$44.84 MSRP: $67.44
You Save: $22.60 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly-Hood Lock Control; Release Cable
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2008-2012 Nissan Versa | Base, Entry, S, SL | 4 Cyl 1.6L, 4 Cyl 1.8L | HR16DE, MR18DE
View related parts
Nissan Versa Hood Lock Control Cable Assembly
Part Number: 65620-5EF0A
$42.17 MSRP: $63.42
You Save: $21.25 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly-Hood Lock Control; Release Cable
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2025 Nissan Versa | S, SR, SV | 4 Cyl 1.6 L GAS
View related parts
Nissan Versa Cable Hood Lock
Part Number: 65621-ZW40A
Product Specifications
- Other Name: Cable Assembly-Hood Lock Control; Release Cable
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2009-2012 Nissan Versa | Base, Entry, S, SL | 4 Cyl 1.6L, 4 Cyl 1.8L | HR16DE, MR18DE
View related parts
Nissan Versa Cable Hood Lock
Part Number: 65621-ZR80A
Product Specifications
- Other Name: Cable Assembly-Hood Lock Control; Release Cable
- Replaces: 65621-EL000, 65621-EL00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2010 Nissan Versa | Base, Entry, S, SL | 4 Cyl 1.6L, 4 Cyl 1.8L | HR16DE, MR18DE
View related parts
Nissan Versa Cable Hood Lock
Part Number: 65621-EL00A
Product Specifications
- Other Name: Cable Assembly-Hood Lock Control
- Replaced by: 65621-ZR80A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2009 Nissan Versa | S, SL | 4 Cyl 1.8L | MR18DE
View related parts
Nissan Versa Cable Assembly-Hood Lock
Part Number: 65621-EL000
Product Specifications
- Other Name: Cable Assembly-Hood Lock Control
- Replaced by: 65621-ZR80A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2008 Nissan Versa | S, SL | 4 Cyl 1.8L | MR18DE

Nissan Versa Hood Cable

The Nissan Versa Hood Cable allows a driver to pop the hood quickly and safely to service the engine bay. The Hood Cable runs from the interior release handle to the latch assembly without unnecessary bends or constraints, so the latch instantly disengages when the lever is pulled. Current Nissan Versa models employ a primary Hood Cable that runs from the cabin to a junction under the hood. Then from that junction, shorter secondary cables run to each latch, which reduces the amount of friction and helps to even out the load. A single continuous Hood Cable was applied in earlier setups in the same line, which would stretch over time, so the two-stage arrangement became popular as replacing the worn branch will not mean swapping the entire cable run. No matter the style, moisture will crack the protective sleeves and corrode or stretch the metal strands, leaving the driver unexpectedly with a stuck closed hood. Routine inspections allow the Hood Cable to run freely, meaning you can easily access the critical components in your Nissan Versa.

If you need any OEM Nissan Versa Hood Cable, feel free to choose them out of our huge selection of genuine Nissan Versa Hood Cable. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Versa Hood Cable Parts Questions & Experts Answers

Cable Hood Lock
65620-EL00A
Q: How to replace the Hood Cable and Hood Latch on the Nissan Versa?
A:
To replace the latch, first remove the radiator Grille, then scribe a line around the latch for alignment, and take out the latch retaining bolts to remove the latch. Disconnect the hood release cable by prying out the cable retainer from the rear of the latch assembly and disengaging the cable. For installation, reverse the removal process, ensuring the latch is adjusted so the hood engages securely when closed and the hood bumpers are slightly compressed. To replace the cable, disconnect it from the latch assembly, remove the left inner fender well liner, detach the cable from the clips along its length, and take out the inside hood release handle to disconnect the cable. Pull the cable grommet into the passenger compartment and then pull the cable through the hole. For installation, reverse the removal process, making sure to push on the grommet with your fingers from the passenger compartment to seat it correctly in the firewall.