How do you remove and install a front crankshaft seal on Nissan Armada?

Remove the crankshaft pulley. The seal is usually installed in the front cover and the main way of removing the seal is using a seal removal tool or a large screwdriver; be very delicate all the time otherwise the seal bore or the crankshaft may be damaged. Around the area where the seal connects to its housing, it is advisable not to scratch or gouge the housing or distort the corresponding part of the seal, since this will result into an oil leak. Scrub the bore to remove old seal material and dirt as well as to also remove corrosive materials from the surface. Place the new seal into the bore so the lip is inside the engine, towards the bore axis and apply a drop of oil to the outside of the seal and the inner surface of the lip. Place the bore onto the shaft and drive the seal into the bore with a seal driver or a large socket and tap it with a hammer until it is in the right position against the cover flange, and that the outside diameter of the socket matches that of the seal. Check the condition of the crankshaft pulley and more specifically the area that comes into contact with the oil seal should be grooved if the contact is frequent replace the crankshaft pulley. Apply engine oil on the seal lips and refit the crankshaft pulley with the help of the retaining bolt and tighten the same to the recommended torque. Reversal of the removal process completes the installation process, after which you should start the engine and inspect it for any signs of oil leakage.

Genuine Nissan Armada Crankshaft Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Crankshaft Seals found

View related parts
Nissan Armada Seal-Oil CRANKSHAFT Front
Part Number: 13510-0Z400
$12.84 MSRP: $17.70
You Save: $4.86 (28%)
ADD TO CART
Product Specifications
- Other Name: Seal-Oil,Crankshaft Front
- Manufacturer Note: NDK
- Position: Front
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Armada | LE, LE/SL, Platinum, SE, SE/SV | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Armada Seal-Oil,CRANKSHAFT Rear
Part Number: 12279-3TS0A
$40.27 MSRP: $58.32
You Save: $18.05 (31%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Crankshaft Seal, Rear Main Seal, Seal
- Position: Rear
- Replaces: 12279-1LA0A, 12279-AD200, 12279-3TA0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2017-2022 Nissan Armada | Midnight Edition, Platinum, Platinum CP, Platinum Reserve, S, SL, SV | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56VD
View related parts
Nissan Armada Seal-Oil,CRANKSHAFT Rear
Part Number: 12279-4Z001
$37.40 MSRP: $54.17
You Save: $16.77 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal, Seal
- Position: Rear
- Replaces: 12279-4Z000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Armada | LE, LE/SL, Platinum, SE, SE/SV | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Armada Seal-Oil CRANKSHAFT Front
Part Number: 13510-1LA0A
$14.76 MSRP: $20.35
You Save: $5.59 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal-Oil,Crankshaft Front
- Position: Front
- Replaces: 13510-6N210, 13510-6N200
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2017-2023 Nissan Armada | Midnight Edition, Platinum, Platinum CP, Platinum Reserve, S, SL, SV | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56VD
View related parts
Nissan Armada Oil Seal-Crank
Part Number: 12279-3TA0A
$40.27 MSRP: $58.32
You Save: $18.05 (31%)
ADD TO CART
Product Specifications
- Other Name: Seal-Oil,CRANKSHAFT Rear
- Manufacturer Note: MADE IN USA
- Position: Rear
- Replaced by: 12279-3TS0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2017 Nissan Armada | Platinum, Platinum CP, SL, SV | 8 Cyl 5.6L | VK56VD
View related parts
Nissan Armada Retainer-Oil Seal,Rear
Part Number: 12297-1CA0A
$94.44 MSRP: $133.38
You Save: $38.94 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal Retainer
- Position: Rear
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2017-2022 Nissan Armada | Midnight Edition, Platinum, Platinum CP, Platinum Reserve, S, SL, SV | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56VD
View related parts
Nissan Armada Retainer-Oil Seal,Rear
Part Number: 12297-7S000
$84.72 MSRP: $119.67
You Save: $34.95 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal Retainer, Seal Plate
- Position: Rear
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Armada | LE, LE/SL, Platinum, SE, SE/SV | 8 Cyl 5.6L | VK56DE

Nissan Armada Crankshaft Seal

The Crankshaft Seal is a vital part that brings out the reliability and performance factor of the Nissan Armada models. The Crankshaft Seal, O-ring, located at the front of the engine, is aimed at sealing the crankcase from oil leakage to allow proper lubrication. Made of an alloy of metal and rubber is the Crankshaft Seal and is important since it helps in the reduction of contact between moving parts and thereby the wearing of the various parts of the Nissan Armada engine. This Crankshaft Seal fits different Nissan Armada models with detailing the requirements of every generation starting with the powerful first-generation car models and ending up the second-generation ones. A failing Crankshaft Seal means at some point there will be oil leaks, this may ultimately cause problems in the engine and compromise on the safety of the car, this is why replacement is essential. Crankshaft Seal is relatively new product in the automotive market and it is one of the optimal products available in the market because of its material and structures it offer the optimal sealing for crankshaft so it enhances the integrity of the car engine. This also enhances the maximum performance of the Nissan Armada and reduces hazards that may cause damage on the engine part. Since Nissans proclaim to dependability, the Crankshaft Seal in the Nissan Armada is a very important component in Armada's engineering superiorities.

If you need any OEM Nissan Armada Crankshaft Seal, feel free to choose them out of our huge selection of genuine Nissan Armada Crankshaft Seal. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Armada Crankshaft Seal Parts Questions & Experts Answers

Seal-Oil CRANKSHAFT Front
13510-0Z400
Q: How do you remove and install a front crankshaft seal on Nissan Armada?
A:
Remove the Crankshaft Pulley. The seal is usually installed in the front cover and the main way of removing the seal is using a seal removal tool or a large screwdriver; be very delicate all the time otherwise the seal bore or the crankshaft may be damaged. Around the area where the seal connects to its housing, it is advisable not to scratch or gouge the housing or distort the corresponding part of the seal, since this will result into an oil leak. Scrub the bore to remove old seal material and dirt as well as to also remove corrosive materials from the surface. Place the new seal into the bore so the lip is inside the engine, towards the bore axis and apply a drop of oil to the outside of the seal and the inner surface of the lip. Place the bore onto the shaft and drive the seal into the bore with a seal driver or a large socket and tap it with a hammer until it is in the right position against the cover flange, and that the outside diameter of the socket matches that of the seal. Check the condition of the crankshaft pulley and more specifically the area that comes into contact with the oil seal should be grooved if the contact is frequent replace the crankshaft pulley. Apply engine oil on the seal lips and refit the crankshaft pulley with the help of the retaining bolt and tighten the same to the recommended torque. Reversal of the removal process completes the installation process, after which you should start the engine and inspect it for any signs of oil leakage.