How to remove and install a radiator and Coolant Reservoir in a Nissan Murano?

Disconnect the cable from the negative terminal of the battery. Drain the cooling system. Raise the vehicle and support it securely on jackstands. Remove the lower engine splash shield, the air inlet duct, and the radiator top covers. Remove the grille and the hood latch assembly. Remove the horn. Disconnect the coolant reservoir hose from the radiator cap adapter. Disconnect the transaxle cooler hoses from the radiator. Remove the upper radiator hose including the cap and adapter. Disconnect the lower radiator hose from the radiator. Detach the upper radiator mounts by spreading the horseshoe clips to release the rubber bushings. Pull the top of the radiator back and upward to lift it out. With the radiator removed, it can be inspected for leaks and damage. If it needs repair, have a radiator shop or dealer service department perform the work, as special techniques are required. Bugs and dirt can be removed from the radiator with a soft brush, followed by forcing water from a garden hose through the core from the engine side. Don't bend the cooling fins as this is done. Installation is the reverse of the removal procedure. Be sure the radiator mounting pads are seated properly at the base of the radiator. After installation, fill the cooling system with the proper mixture of antifreeze and water. Reconnect the battery and perform the necessary re-learn procedures. Allow the engine to reach normal operating temperature, indicated by the upper radiator hose becoming hot. Recheck the coolant level and add more if required. Check and add transmission fluid as needed. Disconnect the overflow hose from the fitting by the radiator cap. Unbolt the coolant reservoir and remove it from the vehicle. Pour the coolant into a container. Wash out the reservoir, using soapy water and a long brush to make the coolant level easier to read. Inspect the reservoir for cracks and chafing. Replace it if any damage is found. Installation is the reverse of removal.

Genuine Nissan Murano Radiator

Cooling Radiator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Radiators found

View related parts
Nissan Murano Radiator Assembly
Part Number: 21460-1AA5A
$528.40 MSRP: $806.47
You Save: $278.07 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Radiator Assy; Radiator, Radiator Assembly
- Replaced by: 21460-1AM0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2010-2014 Nissan Murano | LE, LE/ROOF, S, SL, SL/ROOF, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Murano Radiator Assembly
Part Number: 21460-CA010
$647.89 MSRP: $915.10
You Save: $267.21 (30%)
ADD TO CART
Product Specifications
- Other Name: Radiator Assy
- Replaced by: 21460-CC00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2003-2007 Nissan Murano | S, SE, SL | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Murano Radiator Assembly
Part Number: 21460-5AA0C
$682.92 MSRP: $1050.38
You Save: $367.46 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Radiator Assy; Radiator, Radiator Assembly
- Replaced by:
- Replaces: 21460-5AA0A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2024 Nissan Murano | Midnight Edition, Platinum, S, SL, SV | 6 Cyl 3.5 L GAS
View related parts
Nissan Murano Radiator Assembly
Part Number: 21460-1AA0A
$408.83 MSRP: $623.98
You Save: $215.15 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Radiator Assy; Radiator, Radiator Assembly
- Replaced by:
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2008-2014 Nissan Murano | LE, LE/ROOF, S, SL, SL/ROOF, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Murano Radiator Assembly
Part Number: 21460-5AF0A
$703.00 MSRP: $1081.27
You Save: $378.27 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Radiator Assy; Radiator
- Replaced by:
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2017 Nissan Murano | Platinum, SL, SV | 4 Cyl 2.5L | QR25DER
View related parts
Nissan Murano Radiator Assembly
Part Number: 21460-5AA0A
$682.92 MSRP: $1050.38
You Save: $367.46 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Radiator Assy; Radiator
- Replaced by: 21460-5AA0C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2015-2019 Nissan Murano | Platinum, S, SL, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Murano Radiator Assembly
Part Number: 21460-1AM0A
$528.40 MSRP: $806.47
You Save: $278.07 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Radiator Assy; Radiator, Radiator Assembly
- Replaced by:
- Replaces: 21460-1AA5A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2010-2014 Nissan Murano | LE, LE/ROOF, S, SL, SL/ROOF, SV | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Murano Radiator Assembly-Sub
Part Number: 21457-5AF0A
$273.15 MSRP: $385.80
You Save: $112.65 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Radiator Assembly-Sub; Radiator
- Replaced by:
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2017 Nissan Murano | Platinum, SL, SV | 4 Cyl 2.5L | QR25DER

Nissan Murano Radiator

The Radiator in Nissan Murano cars plays an important role of cooling system as it is heat exchanger which transfers heat from the coolant to the ambient air. In general case, the radiator has the aluminum core with the plastic or aluminum tanks, although copper/brass types are also possible. It also features a core of fins and tubes within which the coolant can flow, thus passing heat as well. There has been the use of different types of radiators in Nissan Murano over the years: the standard radiator and the performance radiator. Performance radiators are made of lightweight aluminum and some of them may have larger tubes and greater fin density thus improving coolant flow and heat exchange. These can be direct fit radiators or universal, as per the kind of application that the car may be - custom, or for racing. The biggest difference between the stock and performance radiators is the type of materials used in the construction as well as the design and cooling efficiency of the performance models.

If you need any OEM Nissan Murano Radiator, feel free to choose them out of our huge selection of genuine Nissan Murano Radiator. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Murano Radiator Parts Questions & Experts Answers

Radiator Assembly
21460-1AA5A
Q:
How to remove and install a radiator and Coolant Reservoir in a Nissan Murano?
A:
Disconnect the cable from the negative terminal of the battery. Drain the cooling system. Raise the vehicle and support it securely on jackstands. Remove the lower engine splash shield, the air inlet duct, and the radiator top covers. Remove the grille and the hood latch assembly. Remove the horn. Disconnect the coolant reservoir hose from the radiator cap adapter. Disconnect the transaxle cooler hoses from the radiator. Remove the upper radiator hose including the cap and adapter. Disconnect the lower radiator hose from the radiator. Detach the upper radiator mounts by spreading the horseshoe clips to release the rubber bushings. Pull the top of the radiator back and upward to lift it out. With the radiator removed, it can be inspected for leaks and damage. If it needs repair, have a radiator shop or dealer service department perform the work, as special techniques are required. Bugs and dirt can be removed from the radiator with a soft brush, followed by forcing water from a garden hose through the core from the engine side. Don't bend the cooling fins as this is done. Installation is the reverse of the removal procedure. Be sure the radiator mounting pads are seated properly at the base of the radiator. After installation, fill the cooling system with the proper mixture of antifreeze and water. Reconnect the battery and perform the necessary re-learn procedures. Allow the engine to reach normal operating temperature, indicated by the upper radiator hose becoming hot. Recheck the coolant level and add more if required. Check and add transmission fluid as needed. Disconnect the overflow hose from the fitting by the radiator cap. Unbolt the coolant reservoir and remove it from the vehicle. Pour the coolant into a container. Wash out the reservoir, using soapy water and a long brush to make the coolant level easier to read. Inspect the reservoir for cracks and chafing. Replace it if any damage is found. Installation is the reverse of removal.