What is the location and function of the Crankshaft Position sensor on Nissan Pathfinder?

For four-cylinder and 3.3L V6 models, the Crankshaft Position sensor is located at the rear of the engine on the transmission bellhousing. It detects gaps in the flywheel/driveplate gear teeth to determine crankshaft speed which is used by the PCM for engine misfire detection. Remove it from the transmission bellhousing and measure the resistance across its terminals to check the sensor. The resistance should be within a specified range for each engine type. If these values of resistance are not right then it should be replaced by a new one. Faulty wiring harness may be revealed if correct values have been observed in both aforementioned cases. If these are fine, but, then there is a need of diagnosing them before any repair work can be done by qualified facility in PCM. There are two Crankshaft Position sensors for 3.5L V6 models; The Crankshaft Position sensor (POS) mounted on aluminum oil pan section at rear of engine close to transmission bellhousing and The Crankshaft Position sensor (REF) located on aluminum oil pan section at front of engine below crankshaft pulley which serve as gaps detectors using permanent magnet, core and coil that vary voltage signals sent to PCM . These signals which include ignition timing, fuel synchronization and misfire detection are used by PCM . Measure and check this against specified range for REF, Crankshaft Position sensor where R denotes Resistance between terminals should be taken as reference value. If these values of resistance are not correct then it would require replacement with new one while checking also wiring harness for open circuits or damage too as an alternative option if need arises when everything seems alright with both wiring harness and properly functioning sensors being present must be considered before visiting any expert technicians at certified workshops who understand more about how PCMs operate in cars so as fix all errors indicated above (losses). For POS, disconnect electrical connector, verify presence of battery voltage in B+ wire terminal, and check continuity to ground at black wire terminal. After removing the sensor, backprobe signal wire terminal with voltmeter. Touch it with a metal object and pull away fast; this should make voltmeter go to 5.0 volts then down to zero volts again. It must be replaced if the sensor does not respond as described above. Disconnect electrical connector then remove sensor for replacement.

Genuine Nissan Pathfinder Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Crankshaft Position Sensors found

View related parts
Nissan Pathfinder CAMSHAFT Position Sensor
Part Number: 23731-AL61A
$119.78 MSRP: $173.48
You Save: $53.70 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Driver Side
- Replaced by: 23731-AL61D
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2012 Nissan Pathfinder | LE, S, SE, SE Off-Road, Silver Edition, SV, XE | 6 Cyl 4.0L, 8 Cyl 5.6L | VK56DE, VQ40DE
View related parts
Nissan Pathfinder Crankshaft Position Sensor
Part Number: 23731-EA20C
$58.40 MSRP: $84.58
You Save: $26.18 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23731-EA20D
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2012 Nissan Pathfinder | LE, S, SE, SE Off-Road, Silver Edition, SV, XE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Pathfinder Engine Camshaft Position Sensor
Part Number: 23731-JA11B
$93.19 MSRP: $134.95
You Save: $41.76 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Crankshaft Position Sensor; Camshaft Position Sensor, Camshaft Sensor
- Manufacturer Note: F/CAM
- Replaces: 23731-JA11A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2022-2024 Nissan Pathfinder
- 2013-2020 Nissan Pathfinder | Platinum, S, SL, SV | 6 Cyl 3.5L | VQ35DD, VQ35DE
View related parts
Nissan Pathfinder Crankshaft Position Sensor
Part Number: 23731-JA10C
$118.86 MSRP: $172.15
You Save: $53.29 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Crankshaft Sensor
- Replaces: 23731-JA10B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2022-2024 Nissan Pathfinder
- 2013-2020 Nissan Pathfinder | Platinum, S, SL, SV | 6 Cyl 3.5L | VQ35DD, VQ35DE
View related parts
Nissan Pathfinder Crankshaft Position Sensor
Part Number: 23731-EA221
$58.40 MSRP: $84.58
You Save: $26.18 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 23731-EA20D
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2008 Nissan Pathfinder | LE, S, SE, SE Off-Road, XE | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Pathfinder Crankshaft Position Sensor
Part Number: 23731-4M50B
$61.83 MSRP: $89.55
You Save: $27.72 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CAMSHAFT Position Sensor
- Replaced by: 23731-4M50D
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2007-2012 Nissan Pathfinder | LE, SE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Pathfinder Crankshaft Position Sensor
Part Number: 23731-31U11
$91.59 MSRP: $132.65
You Save: $41.06 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Crankshaft Sensor
- Manufacturer Note: MITSUBISHI (REF)
- Replaces: 23731-31U10
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2003 Nissan Pathfinder | LE, SE, XE | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Pathfinder Magnet Sensor Assembly
Part Number: 23731-1S700
$43.74 MSRP: $63.35
You Save: $19.61 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assy-Magnet
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1996-2003 Nissan Pathfinder | LE, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Pathfinder Crankshaft Position Sensor
Part Number: 23731-2Y522
$105.34 MSRP: $152.57
You Save: $47.23 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: UNISIA JECS (VTC)
- Replaced by: 23731-2Y52E
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2002 Nissan Pathfinder | LE, SE, XE | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Pathfinder Crankshaft Position Sensor
Part Number: 23731-4BB0A
$90.71 MSRP: $131.37
You Save: $40.66 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Crankshaft Sensor
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2022 Nissan Pathfinder | Platinum, S, SL, SV | 6 Cyl 3.5 L GAS
View related parts
Nissan Pathfinder Magnet Sensor Assembly
Part Number: 23731-3JT5A
$91.78 MSRP: $132.92
You Save: $41.14 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assy-Magnet
- Manufacturer Note: CRANK SENSOR
- Replaced by: 23731-3JT5B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2014 Nissan Pathfinder | Platinum, SL, SV | 4 Cyl 2.5L | QR25DER
View related parts
Nissan Pathfinder Crankshaft Position Sensor
Part Number: 23731-AL605
Product Specifications
- Replaced by: 23731-AL60C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2002-2004 Nissan Pathfinder | LE, SE | 6 Cyl 3.5L | VQ35DE
View related parts
Nissan Pathfinder Crankshaft Position Sensor
Part Number: 23731-AL606
Product Specifications
- Replaced by: 23731-AL60C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2003-2004 Nissan Pathfinder | LE, SE | 6 Cyl 3.5L | VQ35DE

Nissan Pathfinder Crankshaft Position Sensor

The Nissan Pathfinder Crankshaft Position Sensor is an important part which plays a vital role in increasing the quality and efficiency of Nissan Pathfinder models. This sensor carefully keeps an eye at the crankshaft's position and the rate of its rotation while sending important information to the powertrain control module. The nissa part called Crankshaft Position Sensor helps the vehicle to inject fuel correctly and ignite it at the right time, which is the key to powerful and effective drive, both on a daily commute and off-road. Appropriate for installation to Pathfinder models of different generations, including R50, R51, R52, as well as for the new R53, this sensor is produced taking into account the particular requirements of every generation. Crankshaft Position Sensor of Nissan Pathfinder is highly reliable due to its enhanced features like inductive and Hall effect sensor which having their own specialties to track the crankshaft movement. Besides a better performance of the engine, this reliability also adds to the safety profile of the vehicle and can just as well eliminate opportunities for possible starting troubles or stalling of the engine. Moreover, there is one more distinguishing feature of the Nissan Pathfinder Crankshaft Position Sensor in the automotive market, the level of its accuracy and sturdiness which makes this component highly popular among the Pathfinder owners who value powerful car performance and longevity of their vehicle. In conclusion, the Nissan Pathfinder Crankshaft Position Sensor is an important part that encapsulates Nissan's values in the car manufacturing business.

If you need any OEM Nissan Pathfinder Crankshaft Position Sensor, feel free to choose them out of our huge selection of genuine Nissan Pathfinder Crankshaft Position Sensor. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Pathfinder Crankshaft Position Sensor Parts Questions & Experts Answers

Crankshaft Position Sensor
23731-31U11
Q: What is the location and function of the Crankshaft Position sensor on Nissan Pathfinder?
A:
For four-cylinder and 3.3L V6 models, the Crankshaft Position sensor is located at the rear of the engine on the transmission bellhousing. It detects gaps in the flywheel/driveplate gear teeth to determine crankshaft speed which is used by the PCM for engine misfire detection. Remove it from the transmission bellhousing and measure the resistance across its terminals to check the sensor. The resistance should be within a specified range for each engine type. If these values of resistance are not right then it should be replaced by a new one. Faulty wiring harness may be revealed if correct values have been observed in both aforementioned cases. If these are fine, but, then there is a need of diagnosing them before any repair work can be done by qualified facility in PCM. There are two Crankshaft Position sensors for 3.5L V6 models; The Crankshaft Position sensor (POS) mounted on aluminum oil pan section at rear of engine close to transmission bellhousing and The Crankshaft Position sensor (REF) located on aluminum oil pan section at front of engine below crankshaft pulley which serve as gaps detectors using permanent magnet, core and coil that vary voltage signals sent to PCM . These signals which include ignition timing, fuel synchronization and misfire detection are used by PCM . Measure and check this against specified range for REF, Crankshaft Position sensor where R denotes Resistance between terminals should be taken as reference value. If these values of resistance are not correct then it would require replacement with new one while checking also wiring harness for open circuits or damage too as an alternative option if need arises when everything seems alright with both wiring harness and properly functioning sensors being present must be considered before visiting any expert technicians at certified workshops who understand more about how PCMs operate in cars so as fix all errors indicated above (losses). For POS, disconnect electrical connector, verify presence of battery voltage in B+ wire terminal, and check continuity to ground at black wire terminal. After removing the sensor, backprobe signal wire terminal with voltmeter. Touch it with a metal object and pull away fast; this should make voltmeter go to 5.0 volts then down to zero volts again. It must be replaced if the sensor does not respond as described above. Disconnect electrical connector then remove sensor for replacement.

Related Nissan Pathfinder Parts

Browse by Year