How to remove and install a power steering pump on Nissan Titan?

Remove the power steering pump reservoir by pulling it up off of its bracket. Next, drain the fluid from it and properly dispose of the same and then remove the reservoir bracket by taking out the fasteners. Detach the air intake duct. After this, proceed to remove the drivebelt. Disconnect pressure sensor electrical connector which includes power steering pump electrical connector, pressure line fitting and feed hose clamp. Remove pressure line and feed hose from pump. Discard sealing washers on both sides of the pressure line fitting and cap hoses. Finally, unscrew mounting fasteners and remove pump from vehicle but do not spill fluid on painted surfaces. Use holes in pulley to access power steering pump mounting fastener screws. To install: Position pump onto mounting bracket then install mounting fasteners. Tighten fasteners. Connect pressure line and feed hose to pump. Ensure new sealing washers are used on pressure line fitting and tighten banjo bolt.Install drivebelt.Remaining installation is reversal of removal.Fill recommended fluid into power steering reservoir, then bleed system using method that will be given below.

Genuine Nissan Titan Power Steering Pump

Power Steering Pump Unit

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Power Steering Pumps found

View related parts
Nissan Titan Power Steering Pump Assembly
Part Number: 49110-7S000
$493.49 MSRP: $750.78
You Save: $257.29 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy-Power Steering
- Replaced by: 49110-ZV00A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2010 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Pump Power Steering
Part Number: 49110-EZ40A
$395.43 MSRP: $601.12
You Save: $205.69 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy-Power Steering; Power Steering Pump
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2019 Nissan Titan | Platinum, PRO-4X, S, SL, SV, SV/Comf | 8 Cyl 5.0L Diesel | CEV8D1
View related parts
Nissan Titan Pump Power Steering
Part Number: 49110-EZ30C
$358.40 MSRP: $544.60
You Save: $186.20 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy-Power Steering; Power Steering Pump
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2024 Nissan Titan | Platinum, Platinum Reserve, PRO-4X, S, SL, SV, SV/Comf | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56VD
View related parts
Nissan Titan Pump Power Steering
Part Number: 49110-ZV00A
$493.49 MSRP: $750.78
You Save: $257.29 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy-Power Steering; Power Steering Pump
- Replaces: 49110-7S000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Power Steering Pump Assembly
Part Number: 49110-EZ30B
$669.25 MSRP: $1019.03
You Save: $349.78 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assy-Power Steering; Power Steering Pump
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2024 Nissan Titan | Platinum, Platinum Reserve, PRO-4X, S, SL, SV, SV/Comf | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56VD

Nissan Titan Power Steering Pump

Nissan Titan Power Steering Pump is designed to supply hydraulic pressure that lightens steering effort by boosting the torque the driver applies to the wheel. The Power Steering Pump on Nissan models is driven by the crankshaft through a V-belt or serpentine belt, while on Titan trucks the fluid reservoir can either sit on the pump itself or be mounted remotely and linked by a hose. Under everyday driving conditions, Nissan Titan owners rely on steady pressure. The Power Steering Pump pushes high pressure fluid to a steering control valve that channels flow to either side of a hydraulic cylinder piston so the linkage receives assist in the chosen turning direction. Equalized pressure keeps the wheels centered. After doing its work, the fluid returns through a low pressure hose to the Power Steering Pump for recirculation. A Nissan steering system that shows leaks, whining or squealing noises, or requires increased effort at parking speeds may indicate that the Titan owner has a weakening Power Steering Pump that should be checked for proper output pressure.

If you need any OEM Nissan Titan Power Steering Pump, feel free to choose them out of our huge selection of genuine Nissan Titan Power Steering Pump. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Titan Power Steering Pump Parts Questions & Experts Answers

Power Steering Pump Assembly
49110-7S000
Q: How to remove and install a power steering pump on Nissan Titan?
A:
Remove the power steering pump reservoir by pulling it up off of its bracket. Next, drain the fluid from it and properly dispose of the same and then remove the reservoir bracket by taking out the fasteners. Detach the air intake duct. After this, proceed to remove the drivebelt. Disconnect pressure sensor electrical connector which includes power steering pump electrical connector, pressure line fitting and feed hose clamp. Remove pressure line and feed hose from pump. Discard sealing washers on both sides of the pressure line fitting and cap hoses. Finally, unscrew mounting fasteners and remove pump from vehicle but do not spill fluid on painted surfaces. Use holes in pulley to access power steering pump mounting fastener screws. To install: Position pump onto mounting bracket then install mounting fasteners. Tighten fasteners. Connect pressure line and feed hose to pump. Ensure new sealing washers are used on pressure line fitting and tighten banjo bolt.Install drivebelt.Remaining installation is reversal of removal.Fill recommended fluid into power steering reservoir, then bleed system using method that will be given below.