How do you remove lifters,camshafts and Camshaft Seal on 3.3L V6 Nissan Xterra?

To take out the Lash Adjusters, begin by removing the valve cover and rocker arm shaft assemblies. Use rubber bands to keep them in place so that they don't come off from their guides. The Lash Adjuster guide assembly is then removed and Lash Adjusters are taken out of the bores one at a time, keeping them in order. They should not be laid on their side or upside down to avoid trapping air inside. If you feel like there is trapped air, put back the rocker arms, shafts as well as, valve covers and run the engine for 10 minutes at 1000 rpm to bleed the air out of the Lash Adjusters. While they are outside of the engine, check for wear by examining them again so that you can replace if needed. To get rid of camshafts remove heads and pry camshaft cover plate gently from there (Gillespie 7). When unscrewing retaining bolt hold it with holding lugs tightening it accordingly till you remove thrust plate and bolt. The camshaft oil seal should be removed with caution to prevent scuffing or scratching it as it is being pulled out. By rotating in twist squeeze motion pull oronsealpacificcamshaft out of cylinder head (Olay/Weisman Architects). Camshafts are lubricated on bearing journals and lobes using moly-based engine assembly lube before they are cautiously placed into position in the cylinder head (Olay/Weisman Architects). Install camshaft thrust plates with their retaining bolts and ensure that I have checked if my camshafts have any end play (Olay/Weisman Architects). In case endplay does not fall within certain range then thrust plate has to be replaced (Olay/Weisman Architects). Set up camshaft oil seal thus finishing assembling cylinder head.

Genuine Nissan Xterra Camshaft

Cam

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Camshafts found

View related parts
Nissan Xterra Camshaft Assy
Part Number: 13061-1W600
$526.58 MSRP: $743.75
You Save: $217.17 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 13061-1W696
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | SE, XE | 6 Cyl 3.3L | VG33E, VG33ER
View related parts
Nissan Xterra Camshaft Assy
Part Number: 13020-F4521
$58.52 MSRP: $80.67
You Save: $22.15 (28%)
Product Specifications
- Replaced by: 13020-F450A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Xterra Camshaft Assy
Part Number: 13020-F4520
$113.23 MSRP: $159.93
You Save: $46.70 (30%)
Product Specifications
- Replaced by: 13020-F451A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Xterra Camshaft Assy
Part Number: 13020-F4411
$241.91 MSRP: $341.68
You Save: $99.77 (30%)
Product Specifications
- Replaced by: 13020-9E001
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2001 Nissan Xterra | XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Xterra Camshaft Assy
Part Number: 13001-1W600
Product Specifications
- Replaced by: 13001-1W696
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Xterra | SE, XE | 6 Cyl 3.3L | VG33E, VG33ER
View related parts
Nissan Xterra CAMSHAFT Kit (6ZV7)
Part Number: 13020-EA025
$641.15 MSRP: $905.58
You Save: $264.43 (30%)
Product Specifications
- Other Name: Camshaft Assy; Camshaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2015 Nissan Xterra | Base Camp, Off-Road, PRO-4X, S, SE, X | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Xterra Camshaft Assy
Part Number: 13020-F4523
$58.52 MSRP: $80.67
You Save: $22.15 (28%)
Product Specifications
- Replaced by: 13020-F450A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004 Nissan Xterra | XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Xterra Camshaft Assy
Part Number: 13020-F4515
Product Specifications
- Other Name: Camshaft
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2001 Nissan Xterra | XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Xterra Camshaft Assy
Part Number: 13001-EK800
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2003-2004 Nissan Xterra | SE, XE | 6 Cyl 3.3L | VG33E, VG33ER
View related parts
Nissan Xterra Camshaft Assy
Part Number: 13061-EK800
$190.32 MSRP: $268.82
You Save: $78.50 (30%)
Product Specifications
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2003-2004 Nissan Xterra | SE, XE | 6 Cyl 3.3L | VG33E, VG33ER

Nissan Xterra Camshaft

By all this, it is evident that the Camshaft is an essential component that boosts the functionality of Nissan Xterra automobiles. Constructed from cast iron or steel it is a rigid component typically, the Camshaft serves the function of controlling the opening and closing of the intake and exhaust valves so as to facilitate air and fuel consumption. This cuts a fine figure for the Nissan Xterra's V6 engineering which powers this car and is one of the favorite choices of the off road racing marines. Camshaft configuration includes OHV, SOHC, and DOHC as the power required may differ with the models of the Xterra. Besides increasing the valve lift and duration to increase the engine's horsepower, the Camshaft is also designed to improve efficiency of fuel and decrease emissions to meet modern safety and environment concerns. Its versatility in operation helps it to fit in the various Xterra models thus, the ability to provide enhanced performance of the Camshaft is not limited by the kind of configuration of the driver's car. Besides, further specific elements of the Camshaft's profile include the lobe separation angle (LSA) that permits the specific tuning to match the driver's inclination in a car and ensure the Camshaft's domination in the automotive market. In general, the Camshaft distinguishes as an important factor that improves both the performance and safety of Nissan Xterra, thus, making it perfect for adventurers who will never settle for less in terms of performance and safety of the Nissan Xterra.

If you need any OEM Nissan Xterra Camshaft, feel free to choose them out of our huge selection of genuine Nissan Xterra Camshaft. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Xterra Camshaft Parts Questions & Experts Answers

Camshaft Assy
13061-1W600
Q: How do you remove lifters,camshafts and Camshaft Seal on 3.3L V6 Nissan Xterra?
A:
To take out the Lash Adjusters, begin by removing the valve cover and rocker arm shaft assemblies. Use rubber bands to keep them in place so that they don't come off from their guides. The Lash Adjuster guide assembly is then removed and Lash Adjusters are taken out of the bores one at a time, keeping them in order. They should not be laid on their side or upside down to avoid trapping air inside. If you feel like there is trapped air, put back the rocker arms, shafts as well as, valve covers and run the engine for 10 minutes at 1000 rpm to bleed the air out of the Lash Adjusters. While they are outside of the engine, check for wear by examining them again so that you can replace if needed. To get rid of camshafts remove heads and pry camshaft cover plate gently from there (Gillespie 7). When unscrewing retaining bolt hold it with holding lugs tightening it accordingly till you remove thrust plate and bolt. The camshaft oil seal should be removed with caution to prevent scuffing or scratching it as it is being pulled out. By rotating in twist squeeze motion pull oronsealpacificcamshaft out of Cylinder Head (Olay/Weisman Architects). Camshafts are lubricated on bearing journals and lobes using moly-based engine assembly lube before they are cautiously placed into position in the cylinder head (Olay/Weisman Architects). Install camshaft thrust plates with their retaining bolts and ensure that I have checked if my camshafts have any end play (Olay/Weisman Architects). In case endplay does not fall within certain range then thrust plate has to be replaced (Olay/Weisman Architects). Set up camshaft oil seal thus finishing assembling cylinder head.