How to inspect and replace the rubber brake line hoses on the Nissan Titan?

Once every six months, with the car raised and held up by jackstands, test the rubber hoses between steel brake lines and wheel and brake parts for splits, rubbing, wetness, bubbles, and breaks, as these brake parts are weak and easily damaged. Replace old, worn hoses with new ones immediately when you see them. To change broken front flexible brake hoses, loosen the wheel's bolts, lift the car, and take off the wheel. Loosen and remove the flare-nut wrench fitting from the brake hose at the frame bracket, then pull off the hose bracket attached to the steering knuckle. Pull out the U-clip from its place on the arm holding the hose, then move the hose through this gap. First, remove the bolt from the inlet at the caliper end, then separate the hose from the component and toss out the old copper seals. Place the new hose on the caliper and thread the inlet fitting bolt through with fresh sealant washers. Tighten the bolt to the recommended torque. Put the hose into the frame bracket, straighten it out, join the brake line adapter, put the U-clip on, and fasten everything tight. Then put the wheel in place on the tire, attach the lug nuts, let the car down, and snug up the lug nuts to their proper torque setting. Keep the car lifted and secure with jackstands on both sides, making sure the front wheels can't move. Remove the female fitting on the hose at the rear axle housing by unscrewing the brake line fitting with a flare-nut wrench. Take out the U-clip from the bracket's fitting, and guide the hose into place. For Titans, detach the brake hose from the caliper, and detach both rigid brake line connections at the rear axle housing bracket. Following replacing these parts, reinstall lug nuts. During installation, we always put fresh washers over the fitting seals. When changing the brake lines, install them with the right steel tools and never put in copper sections instead. Pre-cut brake lines with tips already on come ready to install, but need to be shaped the right way with a bent tool that applies lubrication. Mount and fix the new pipe in bracket positions, making sure it stays put and leaves enough space from moving or hot engine pieces. First, inspect and top up the fluid in the master cylinder, then purify the braking system, and finally, carefully test your brakes before driving again.

Genuine Nissan Titan Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

44 Brake Lines found

View related parts
Nissan Titan Brake Tube Assembly Front Left Hand
Part Number: 46242-7S210
$9.28 MSRP: $13.44
You Save: $4.16 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube Assy-Brake,Front LH
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Brake Tube Assembly Front Right Hand
Part Number: 46240-7S210
$9.28 MSRP: $13.43
You Save: $4.15 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube Assy-Brake,Front RH; Brake Tube
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2024 Nissan Titan | LE, Off-Road, Platinum, Platinum Reserve, PRO-4X, S, SE, SL, SV, SV/Comf, XE | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56DE, VK56VD
View related parts
Nissan Titan Tube Assy-Rear Brake,LH
Part Number: 46310-7S200
$75.13 MSRP: $106.12
You Save: $30.99 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Tube Assembly-Rear Brake,R
Part Number: 46290-8S100
$83.59 MSRP: $118.07
You Save: $34.48 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube Assy-Rear Brake,RH
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Tube Assembly-Brake,Front L
Part Number: 46242-7S200
$93.36 MSRP: $135.21
You Save: $41.85 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube Assy-Brake,Front LH
- Position: Driver side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Tube Assembly-Brake,Front R
Part Number: 46240-7S200
$38.62 MSRP: $55.93
You Save: $17.31 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube Assy-Brake,Front RH
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Brake Hose Assembly
Part Number: 46210-ZV11A
$46.00 MSRP: $66.62
You Save: $20.62 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy-Brake; Brake Hose, Flex Hose
- Replaces: 46210-1Z600
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Brake Hose Assembly Front
Part Number: 46211-7S002
$53.66 MSRP: $77.72
You Save: $24.06 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy-Brake,Front; Brake Hose, Flex Hose
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2008 Nissan Titan | LE, SE, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Brake Front Hose Assembly
Part Number: 46210-ZV01B
$42.45 MSRP: $61.48
You Save: $19.03 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy-Brake,Front; Brake Hose, Flex Hose
- Position: Front
- Replaced by: 46210-ZV01C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2010-2019 Nissan Titan | LE, Off-Road, Platinum, PRO-4X, S, SE, SL, SV, SV/Comf, XE | 8 Cyl 5.6L | VK56DE, VK56VD
View related parts
Nissan Titan Brake Hose Assembly
Part Number: 46210-1Z600
$46.00 MSRP: $66.62
You Save: $20.62 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy-Brake
- Replaced by: 46210-ZV11A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2011 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Brake Front Hose Assembly
Part Number: 46211-ZV01B
$42.45 MSRP: $61.48
You Save: $19.03 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy-Brake,Front; Brake Hose, Flex Hose
- Position: Front
- Replaced by: 46211-ZV01C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2010-2019 Nissan Titan | LE, Off-Road, Platinum, PRO-4X, S, SE, SL, SV, SV/Comf, XE | 8 Cyl 5.6L | VK56DE, VK56VD
View related parts
Nissan Titan Brake Hose Assembly
Part Number: 46210-7S300
$38.46 MSRP: $55.70
You Save: $17.24 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy-Brake
- Replaced by: 46210-ZV10A
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2011 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Brake Hose Assembly
Part Number: 46210-EZ06B
$52.33 MSRP: $75.78
You Save: $23.45 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy-Brake; Brake Hose, Flex Hose
- Position: Passenger Side
- Replaced by: 46210-EZ06C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2019 Nissan Titan | Platinum, PRO-4X, S, SL, SV, SV/Comf | 8 Cyl 5.6L | VK56VD
View related parts
Nissan Titan Brake Hose Assembly Front
Part Number: 46210-7S002
$36.81 MSRP: $53.32
You Save: $16.51 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy-Brake,Front; Brake Hose, Flex Hose
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2008 Nissan Titan | LE, SE, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Brake Hose Assembly
Part Number: 46210-ZV10A
$38.46 MSRP: $55.70
You Save: $17.24 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy-Brake; Brake Hose, Flex Hose
- Replaces: 46210-7S300
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2004-2015 Nissan Titan | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 8 Cyl 5.6L | VK56DE
View related parts
Nissan Titan Brake Hose Assembly
Part Number: 46210-EZ56A
$57.86 MSRP: $83.80
You Save: $25.94 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assy-Brake; Brake Hose, Flex Hose
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2024 Nissan Titan | Platinum, Platinum Reserve, PRO-4X, S, SL, SV, SV/Comf | 8 Cyl 5.0 L DIESEL, 8 Cyl 5.0L Diesel, 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | CEV8D1, VK56VD
View related parts
Nissan Titan Brake Hose Assembly
Part Number: 46211-EZ55D
$57.22 MSRP: $82.87
You Save: $25.65 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE ASSY-BRAKE; Brake Hose, Brake Tube
- Position: Driver Side
- Replaces: 46211-EZ55C, 46211-EZ55B, 46211-EZ55E
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2024 Nissan Titan | PRO-4X, Platinum Reserve, S, SL, SV | 8 Cyl 5.0 L DIESEL, 8 Cyl 5.6 L GAS
View related parts
Nissan Titan Brake Hose Assembly
Part Number: 46210-EZ55C
$26.48 MSRP: $38.35
You Save: $11.87 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE ASSY-BRAKE; Brake Hose, Flex Hose
- Replaces: 46210-EZ55A, 46210-EZ55D, 46210-EZ55B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2024 Nissan Titan | PRO-4X, Platinum Reserve, S, SL, SV | 8 Cyl 5.0 L DIESEL, 8 Cyl 5.6 L GAS
View related parts
Nissan Titan Brake Hose Assembly
Part Number: 46210-EZ05D
$28.54 MSRP: $41.33
You Save: $12.79 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE ASSY-BRAKE; Brake Hose, Flex Hose
- Replaces: 46210-EZ05C, 46210-EZ05E, 46210-EZ05A, 46210-EZ05B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2024 Nissan Titan | PRO-4X, Platinum Reserve, S, SL, SV | 8 Cyl 5.6 L GAS
View related parts
Nissan Titan Tube Assy-Rear Brake,RH
Part Number: 46290-EZ00B
$51.59 MSRP: $71.12
You Save: $19.53 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Tube
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2024 Nissan Titan | Platinum, Platinum Reserve, PRO-4X, S, SL, SV, SV/Comf | 8 Cyl 5.6 L GAS, 8 Cyl 5.6L | VK56VD

| Page 1 of 3 |Next >

1-20 of 44 Results

Nissan Titan Brake Line

The Nissan Titan Brake Line carries brake fluid from the master cylinder to the calipers or wheel cylinders, allowing hydraulic pressure to reach the brakes when the pedal is pressed. The Brake Line is made of metal tubing routed along the frame or flexible hose sections near the wheels. This creates a sealed path that ensures braking force remains firm and consistent. The metal sections undergo corrosion or denting due to impact with road salt, debris, and off-road use while the rubber hose sections crack, bulge, and may suffer internal damage that restricts fluid flow. When there is a leak or obstruction in any segment of the Brake Line, the pressure will decrease, making the pedal mushy. Thus, it leads to loss of control. Routine inspections for damp patches, deformations, and fissures are essential so each Nissan Titan can stop safely. You can find prebent stainless steel lines with the correct fittings or direct fit hoses if replacement is necessary. Each offers the exact diameter and length specified for Nissan Titan models and will restore the integrity of the Brake Line network. Any Nissan Titan with a faulty Brake Line should be replaced promptly.

If you need any OEM Nissan Titan Brake Line, feel free to choose them out of our huge selection of genuine Nissan Titan Brake Line. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Titan Brake Line Parts Questions & Experts Answers

Brake Tube Assembly Front Left Hand
46242-7S210
Q: How to inspect and replace the rubber brake line hoses on the Nissan Titan?
A:
Once every six months, with the car raised and held up by jackstands, test the rubber hoses between steel brake lines and wheel and brake parts for splits, rubbing, wetness, bubbles, and breaks, as these brake parts are weak and easily damaged. Replace old, worn hoses with new ones immediately when you see them. To change broken front flexible brake hoses, loosen the wheel's bolts, lift the car, and take off the wheel. Loosen and remove the flare-nut wrench fitting from the brake hose at the frame bracket, then pull off the hose bracket attached to the steering knuckle. Pull out the U-clip from its place on the arm holding the hose, then move the hose through this gap. First, remove the bolt from the inlet at the caliper end, then separate the hose from the component and toss out the old copper seals. Place the new hose on the caliper and thread the inlet fitting bolt through with fresh sealant washers. Tighten the bolt to the recommended torque. Put the hose into the frame bracket, straighten it out, join the brake line adapter, put the U-clip on, and fasten everything tight. Then put the wheel in place on the tire, attach the lug nuts, let the car down, and snug up the lug nuts to their proper torque setting. Keep the car lifted and secure with jackstands on both sides, making sure the front wheels can't move. Remove the female fitting on the hose at the rear axle housing by unscrewing the brake line fitting with a flare-nut wrench. Take out the U-clip from the bracket's fitting, and guide the hose into place. For Titans, detach the brake hose from the caliper, and detach both rigid brake line connections at the rear axle housing bracket. Following replacing these parts, reinstall lug nuts. During installation, we always put fresh washers over the fitting seals. When changing the brake lines, install them with the right steel tools and never put in copper sections instead. Pre-cut brake lines with tips already on come ready to install, but need to be shaped the right way with a bent tool that applies lubrication. Mount and fix the new pipe in bracket positions, making sure it stays put and leaves enough space from moving or hot engine pieces. First, inspect and top up the fluid in the master cylinder, then purify the braking system, and finally, carefully test your brakes before driving again.