How to install a Piston Ring Set on the Nissan Frontier?

Make sure you have checked the clearance that exists between the side of the piston and rings before installing piston rings. Organize the assembly of pistons/rods and new ring sets to correspond with the same cylinder and pistons for end gap measurement during engine installation. Fit the first cylinder with top (number one) ring, by pressing it down using its top thereby aligning it with cylinders walls. Place that ring towards the bottom of a cylinder since some measurements should be taken at this location. For end gap measurement, use feeler gauges and locate a gauge that slightly drags upon closing it, which is essentially similar to the width of the opening when completely shut. At any rate, compare this value to specifications; if it is beyond or below those values you need to have correct rings at hand before continuing on your way. If the gap is too small, either file them in order to fit or replace them depending on their material and type. The maximum specified end gap will depart from excess end gap, which is not as critical unless greater than 0.040-inch. In case filing becomes necessary, files should be used carefully in cutting up edges around ring gaps. Keep all parts matched while going through all cylinders for each ring repeatedly doing this task until completion Once you are through with checking or correcting gaps in ring ends, commence installing rings onto pistons Begin with oil control ring by inserting expander/spacer into groove making sure anti-rotation tab (if present) is properly positioned and install side rails without using any ring installation tool Verify smooth movement of lower and upper side rails within a groove meant for a ring The stamp can typically be found toward number two (middle) rings; insert it facing upwards into a piston with extreme caution not to overexpand these while putting them on Take care also not to mix up different cross-sections between upper most part marked "TOP" and one embossed "2ND", which designates number one (top) ring. All pistons and their rings will be subjected to this procedure again.

Genuine Nissan Frontier Piston Ring Set

Piston Ring

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

23 Piston Ring Sets found

View related parts
Nissan Frontier Piston Ring Set
Part Number: 12033-8J100
$310.25 MSRP: $438.20
You Save: $127.95 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Ring Set-Piston; Piston Ring Set
- Manufacturer Note: STD
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2013 Nissan Frontier | LE, Off-Road, PRO-4X, S, SE, SL, SV | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Ring Set Piston
Part Number: 12033-EA00B
$185.97 MSRP: $262.67
You Save: $76.70 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Ring Set-Piston; Piston Ring Set
- Manufacturer Note: STD
- Replaced by: 12033-EA00C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2008-2018 Nissan Frontier | S, SE, SV, XE | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Frontier Piston Ring Set
Part Number: 12033-0Z810
$151.65 MSRP: $214.12
You Save: $62.47 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Ring Set-Piston. This item subject to a 40% restocking fee if returned.; Piston Ring Set
- Manufacturer Note: STD
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Frontier | XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Frontier Piston Ring Set
Part Number: 12033-EA000
$185.97 MSRP: $262.67
You Save: $76.70 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Ring Set-Piston
- Manufacturer Note: STD
- Replaced by: 12033-EA00C
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2009 Nissan Frontier | XE | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Frontier Ring Set Piston
Part Number: 12033-9BT0A
$264.03 MSRP: $372.92
You Save: $108.89 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Piston Rings
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2024 Nissan Frontier | Hardbody Edition, PRO-4X, PRO-X, S, SL, SV | 6 Cyl 3.8 L GAS
View related parts
Nissan Frontier Ring Set Piston
Part Number: 12033-EA00C
$185.97 MSRP: $262.67
You Save: $76.70 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Piston Ring Set
- Manufacturer Note: STD
- Replaces: 12033-EA000, 12033-EA00B
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2005-2019 Nissan Frontier | S, SE, SV, XE | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Frontier Ring Set Piston
Part Number: 12035-9BT0A
$278.90 MSRP: $393.93
You Save: $115.03 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Piston Rings
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2020-2024 Nissan Frontier | Hardbody Edition, PRO-4X, PRO-X, S, SL, SV | 6 Cyl 3.8 L GAS
View related parts
Nissan Frontier Piston Ring Set
Part Number: 12033-9BF0A
$305.10 MSRP: $430.93
You Save: $125.83 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Ring Set-Piston; Piston Ring Set
- Manufacturer Note: STD
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Frontier | PRO-4X, S, SL, SV | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Piston Ring Set
Part Number: 12035-EA00B
$194.09 MSRP: $274.13
You Save: $80.04 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Ring Set-Piston; Piston Ring Set
- Manufacturer Note: OS = 0.20
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2017-2019 Nissan Frontier | S, SV | 4 Cyl 2.5L | QR25DE
- 2012-2015 Nissan Frontier | S, SV | 4 Cyl 2.5L | QR25DE
View related parts
Nissan Frontier Piston Ring Set
Part Number: 12035-9BF0A
$252.72 MSRP: $356.95
You Save: $104.23 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Ring Set-Piston
- Manufacturer Note: OS=0.20
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2012-2019 Nissan Frontier | PRO-4X, S, SL, SV | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Piston Ring Set
Part Number: 12036-7B000
$63.45 MSRP: $89.62
You Save: $26.17 (30%)
ADD TO CART
Limited Availability
Product Specifications
- Other Name: Ring Set-Piston
- Manufacturer Note: OS=0.50
- Replaced by: 12036-7Z800
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2002 Nissan Frontier | SC, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Piston Ring Set
Part Number: 12033-9E000
$118.08 MSRP: $166.78
You Save: $48.70 (30%)
Product Specifications
- Other Name: Ring Set-Piston; Piston Ring Set
- Manufacturer Note: STD
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2001 Nissan Frontier | SE, STD, XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Frontier Piston Ring Set
Part Number: 12038-0Z810
Product Specifications
- Other Name: Ring Set-Piston
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Frontier | XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Frontier Piston Ring Set
Part Number: 12036-0Z810
Product Specifications
- Other Name: Ring Set-Piston
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2000-2004 Nissan Frontier | XE | 4 Cyl 2.4L | KA24DE
View related parts
Nissan Frontier Ring Set Piston
Part Number: 12035-9BM0A
Product Specifications
- Other Name: Ring Set-Piston; Piston Ring Set
- Manufacturer Note: OS=0.20
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2019 Nissan Frontier | PRO-4X, S, SL, SV | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Ring Set Piston
Part Number: 12033-9BM0A
Product Specifications
- Other Name: Ring Set-Piston; Piston Ring Set
- Manufacturer Note: STD
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 2016-2019 Nissan Frontier | PRO-4X, S, SL, SV | 6 Cyl 4.0L | VQ40DE
View related parts
Nissan Frontier Ring Set Piston
Part Number: 12036-7Z800
Product Specifications
- Other Name: Ring Set-Piston
- Manufacturer Note: OS=0.50
- Replaces: 12036-7B000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2004 Nissan Frontier | SC, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Ring Set Piston
Part Number: 12035-7Z800
Product Specifications
- Other Name: Ring Set-Piston
- Manufacturer Note: OS=0.25
- Replaces: 12035-7B000
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2004 Nissan Frontier | SC, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Piston Ring Set
Part Number: 12035-7B000
Product Specifications
- Other Name: Ring Set-Piston
- Manufacturer Note: OS=0.25
- Replaced by: 12035-7Z800
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2002 Nissan Frontier | SC, SE, XE | 6 Cyl 3.3L | VG33E
View related parts
Nissan Frontier Piston Ring Set
Part Number: 12036-9E000
Product Specifications
- Other Name: Ring Set-Piston
- Manufacturer Note: OS=0.5
- Warranty: This genuine part is guaranteed by Nissan's factory warranty.
Fits the following Vehicles:
- 1998-2001 Nissan Frontier | SE, STD, XE | 4 Cyl 2.4L | KA24DE

| Page 1 of 2 |Next >

1-20 of 23 Results

Nissan Frontier Piston Ring Set

The Nissan Frontier Piston Ring Set creates a strong seal between each piston and its cylinder so that the engine can generate the pressure that moves the truck forward. The rings prevent the loss of power, guide heat from the piston crown to the cooler cylinder wall, and scrape oil back in the sump to prevent the motor from getting contaminated. This is achieved by sealing gases that blow by. The typical Piston Ring Set includes three rings, two upper compression rings, and one lower oil control ring, designed for Nissan engines, made of tough cast iron or steel and coated with chromium or plasma-sprayed molybdenum for high temperatures. Frontier models have recently introduced Piston Ring Set profiles that are much thinner. The top and second rings are just 1 mm thick while the oil ring is 2 mm thick. These thinner profiles result in less friction, improved bore conformity, and sealing. This is quite an upgrade from previous Piston Ring Set designs which were much thicker. Every Piston Ring Set, whether thin or thick, employs its own spring tension to grip the wall of its cylinder. The recent Piston Ring Set reduces an estimated 25% of mechanical loss resulting from the engine, ensuring consistent Frontier performance and overall Nissan fuel economy.

If you need any OEM Nissan Frontier Piston Ring Set, feel free to choose them out of our huge selection of genuine Nissan Frontier Piston Ring Set. All our parts are offered at unbeatable prices and are supported by the manufacturer's warranty. In addition, we offer quick shipping to have your parts delivered to your door step in a matter of days.

Nissan Frontier Piston Ring Set Parts Questions & Experts Answers

Piston Ring Set
12033-7B000
Q: How to install a Piston Ring Set on the Nissan Frontier?
A:
Make sure you have checked the clearance that exists between the side of the Piston and rings before installing piston rings. Organize the assembly of pistons/rods and new ring sets to correspond with the same cylinder and pistons for end gap measurement during engine installation. Fit the first cylinder with top (number one) ring, by pressing it down using its top thereby aligning it with cylinders walls. Place that ring towards the bottom of a cylinder since some measurements should be taken at this location. For end gap measurement, use feeler gauges and locate a gauge that slightly drags upon closing it, which is essentially similar to the width of the opening when completely shut. At any rate, compare this value to specifications; if it is beyond or below those values you need to have correct rings at hand before continuing on your way. If the gap is too small, either file them in order to fit or replace them depending on their material and type. The maximum specified end gap will depart from excess end gap, which is not as critical unless greater than 0.040-inch. In case filing becomes necessary, files should be used carefully in cutting up edges around ring gaps. Keep all parts matched while going through all cylinders for each ring repeatedly doing this task until completion Once you are through with checking or correcting gaps in ring ends, commence installing rings onto pistons Begin with oil control ring by inserting expander/spacer into groove making sure anti-rotation tab (if present) is properly positioned and install side rails without using any ring installation tool Verify smooth movement of lower and upper side rails within a groove meant for a ring The stamp can typically be found toward number two (middle) rings; insert it facing upwards into a piston with extreme caution not to overexpand these while putting them on Take care also not to mix up different cross-sections between upper most part marked "TOP" and one embossed "2ND", which designates number one (top) ring. All pistons and their rings will be subjected to this procedure again.