How to check the pad lining thickness and replace the front Brake Pad Set for Nissan 240sx?

To check the pad lining thickness, it is possible to do so without removing the pads, and the Brake Specifications chart provides the manufacturer's pad wear limit, although this may differ from state inspection laws. When replacing pads, inspect the rotor surfaces for scoring or wear, and remove them for resurfacing if they are badly scored. All four front brake pads must be replaced as a complete set, and bleeding the brake system should only be done if necessary. For the Type N22 Series, raise the front of the vehicle, remove the wheels, and take out the retaining clip and pad pins before removing the pads. To install, open the bleeder screw slightly, push the outer piston in, install the inner pad, and then the outer pad, applying grease to contact areas while avoiding the friction surfaces. For the Type CL22V Series, raise the front, remove the lower pin bolt, swing the cylinder body upward, and remove the pad retainer and pads without depressing the brake pedal. Clean the piston end, install the inner and outer pads, and tighten the pin bolt. For the Type AD22V Series, remove the road wheel, lower caliper guide pin, and rotate the caliper body upward to remove the pads. Clean the piston end, install the new pads, and tighten the guide pin bolt. For Types CL28VB, CL22VB, and CL25VB, raise the vehicle, remove the front wheel and lower pin bolt, swing the caliper body upward, and remove the pad retainers and shims. Check the fluid level in the master cylinder, use a C-clamp to press the caliper piston back, install new pads with new shims, torque the lower retaining bolt, and ensure the brakes are bled and adjusted as necessary before driving.

How to properly replace the rear Brake Pad Set on a Nissan Juke?

Chock the front wheels, jack up the rear of the car, and support it on axle stands before removing the rear road wheels and fully releasing the handbrake. On one side of the vehicle, push the caliper piston into its bore by pulling the caliper outwards, then unscrew and remove the caliper lower guide pin bolt. Pivot the caliper body upwards to expose the brake pads, securing it in place without depressing the brake pedal, and take care not to strain the brake fluid hose. Note the locations and orientation of the shims and anti-rattle clips, then lift out the brake pads, shims, and clips. Separate the shims from the pads, noting their fitted position, and measure the thickness of each brake pad's friction material; if any pad is worn to the specified minimum thickness or less, all four pads must be renewed, and any fouled pads should also be replaced. If the pads are serviceable, clean them carefully, paying attention to the sides and back of the metal backing, and clean the anti-rattle clips, shims, and brake pad locations in the caliper body. Check that the rubber guide pin gaiters are undamaged, brush away dust and dirt from the caliper and piston, and inspect the dust seal and piston for damage or leaks. If new brake pads are to be fitted, push the caliper piston back into the cylinder using a G-clamp or suitable levers, monitoring the master cylinder reservoir to prevent spillage. Refit the upper and lower anti-rattle clips, apply anti-squeal brake grease to the contact surfaces of the pad backing plates, and refit the shims, ensuring no grease contacts the pad friction linings. Refit the pads and shims in their original positions, pivot the caliper back into place, and tighten the caliper lower guide pin bolt to the specified torque. Check that the caliper body slides smoothly on the guide pins, repeat the procedure on the remaining rear caliper, and after refitting both sets of front brake pads, depress the brake pedal repeatedly until normal pedal pressure is restored. Finally, refit the roadwheels, lower the vehicle to the ground, and check the brake hydraulic fluid level, keeping in mind that new pads will not provide full braking efficiency until they have bedded in, so avoid hard braking for the first hundred miles after renewal.

Genuine Nissan Brake Pad Set

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

365 Brake Pad Sets found

View related parts
Nissan Front Brake Pads Kit
Part Number: D1060-3TA0A
$74.31 MSRP: $107.63
You Save: $33.32 (31%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Front; Brake Pads, Front Pads
- Position: Front
Fits the following Nissan Models:
- Altima | 2013-2020 | 25SL/Moon Roof, Base, Edition ONE, Entry, Platinum, S, S PDS, SL, SR, SV, SV Navigation, Tech | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L, 4 Cyl 2.5 L GAS, 4 Cyl 2.5L, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L
- Leaf | 2013-2017 | S, SL, SV | Electric Motor
View related parts
Nissan Front Brake Pad Disc Kit
Part Number: D1060-3JA0A
$81.65 MSRP: $118.25
You Save: $36.60 (31%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Front; Brake Pads, Front Pads
- Position: Front
Fits the following Nissan Models:
- Murano | 2015-2020 | Platinum, S, SL, SV | 4 Cyl 2.5L, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L
- Pathfinder | 2013-2020 | Platinum, Platinum Hybrid, S, SL, SL Hybrid, SV, SV Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5L, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L
View related parts
Nissan Rear Brake Pads Kit
Part Number: D4060-4CU2A
$76.21 MSRP: $110.38
You Save: $34.17 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Rear; Brake Pads, Rear Pads
- Position: Rear
- Replaces: D4060-4BA0B, D4060-4BA0C
Fits the following Nissan Models:
- Rogue | 2014-2020 | S, SL, SL Hybrid, SL/Premium, SV, SV Hybrid, SV Premium | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0L, 4 Cyl 2.5 L GAS, 4 Cyl 2.5L
- Rogue Sport | 2017-2021 | S, SL, SV | 4 Cyl 2.0 L GAS, 4 Cyl 2.0L
View related parts
Nissan Rear Brake Pad Disc Kit
Part Number: D4060-9HM0B
$76.60 MSRP: $110.93
You Save: $34.33 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Rear; Brake Pads, Rear Pads
- Position: Rear
Fits the following Nissan Models:
- Altima | 2013-2018 | 25SL/Moon Roof, S, S PDS, SL, SR, SV, SV Navigation, Tech | 4 Cyl 2.5L, 6 Cyl 3.5L
- Maxima | 2013-2014 | LE, Premium, S, Sport, SR, SV | 6 Cyl 3.5L
- Sentra | 2013-2019 | Nismo, SL, SR | 4 Cyl 1.6L, 4 Cyl 1.8L
View More
View related parts
Nissan Front Brake Pads Kit
Part Number: D1060-ZP00C
$77.85 MSRP: $112.75
You Save: $34.90 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Front; Brake Pads, Front Pads
- Position: Front
- Replaces: 41060-ZP025, 41060-EA025, 41060-ZP00B, D1060-ZP00B
Fits the following Nissan Models:
- Frontier | 2005-2019 | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 4.0L
- Pathfinder | 2005-2012 | LE, S, SE, SE Off-Road, SV, Silver Edition, XE | 6 Cyl 4.0L
- Xterra | 2005-2015 | Base Camp, Off-Road, PRO-4X, S, SE, X | 6 Cyl 4.0L
View More
View related parts
Nissan Rear Brake Pad Disc Kit
Part Number: D4M60-9N00A
$79.22 MSRP: $114.73
You Save: $35.51 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Rear
- Position: Rear
- Replaced by: D4M60-9N00B
Fits the following Nissan Models:
- Murano | 2009-2019 | LE, LE/ROOF, Platinum, S, SL, SL/ROOF, SV | 4 Cyl 2.5L, 6 Cyl 3.5L
- Pathfinder | 2013-2019 | Platinum, S, SL, SV | 4 Cyl 2.5L, 6 Cyl 3.5L
- Quest | 2011-2017 | LE, S, SL, SV | 6 Cyl 3.5L
View More
View related parts
Nissan Front Brake Pads Kit
Part Number: D1060-4BA0A
$76.21 MSRP: $110.37
You Save: $34.16 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Front
- Position: Front
- Replaced by: D1060-4BT0C
Fits the following Nissan Models:
- Rogue | 2014-2019 | S, SL, SL/Premium, SV, SV Premium | 4 Cyl 2.5L
- Rogue Sport | 2017-2019 | S, SL, SV | 4 Cyl 2.0L
View related parts
Nissan Disc Brake Pad Kit
Part Number: D1060-4BT0C
$76.21 MSRP: $110.37
You Save: $34.16 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Disc Brake; Brake Pads, Front Pads
- Replaces: D1060-4BA0A
Fits the following Nissan Models:
- Rogue | 2020 | S, SL, SL Hybrid, SV, SV Hybrid | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS
- Rogue Sport | 2020-2021 | S, SL, SV | 4 Cyl 2.0 L GAS
View related parts
Nissan Front Brake Pads Kit
Part Number: D1060-EM30C
$74.31 MSRP: $107.63
You Save: $33.32 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Front; Brake Pads, Front Pads
- Position: Front
- Replaces: 41060-2Y091, 41060-8J090, 41060-9J425, 41060-2Y990, 41060-2Y090, 41060-5Y790, 41060-ZB590, D1060-AC20A, D1060-EW81A, D106M-2Y990, D1061-AC20A, D1060-2Y990, D1060-ZB50A, D1060-1FC0A, D1060-9J40A, D1060-EM30A, D1061-EM30C
Fits the following Nissan Models:
- Altima | 2002-2006 | Base, S, SE, SL | 4 Cyl 2.5L, 6 Cyl 3.5L
- Cube | 2009-2014 | 18, S, SL | 4 Cyl 1.8L
- Maxima | 2000-2003 | GLE, GXE, GXEL, SE, SEL, SES | 6 Cyl 3.0L, 6 Cyl 3.5L
- Sentra | 2007-2019 | 20, FE, S, SL, SR, SV | 4 Cyl 1.8L, 4 Cyl 2.0L
- Versa | 2007-2012 | S, SL | 4 Cyl 1.8L
View More
View related parts
Nissan Front Brake Pads Kit
Part Number: 41060-ZP025
$77.85 MSRP: $112.75
You Save: $34.90 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Front
- Position: Front
- Replaced by: D1060-ZP00C
Fits the following Nissan Models:
- Frontier | 2005-2016 | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 4.0L
- Pathfinder | 2005-2012 | LE, S, SE, SE Off-Road, Silver Edition, SV, XE | 6 Cyl 4.0L
- Xterra | 2005-2015 | Base Camp, Off-Road, PRO-4X, S, SE, X | 6 Cyl 4.0L
View More
View related parts
Nissan Rear Brake Pad Disc Kit
Part Number: 44060-EA085
$77.85 MSRP: $112.75
You Save: $34.90 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Rear; Brake Pads, Rear Pads
- Position: Rear
- Replaces: D4060-EA01B
Fits the following Nissan Models:
- Frontier | 2005-2019 | LE, Off-Road, PRO-4X, S, SE, SL, SV, XE | 4 Cyl 2.5L, 6 Cyl 4.0L
- Xterra | 2005-2015 | Base Camp, Off-Road, PRO-4X, S, SE, X | 6 Cyl 4.0L
View related parts
Nissan Front Brake Pads Kit
Part Number: D1060-9FE0A
$81.69 MSRP: $118.32
You Save: $36.63 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Front; Brake Pads, Front Pads
- Position: Front
- Replaced by: D1M60-9FE0A
Fits the following Nissan Models:
- Armada | 2017-2019, 2009-2015 | LE, LE/SL, Platinum, Platinum CP, SE, SE/SV, SL, SV | 8 Cyl 5.6L
- Titan | 2012-2019 | Platinum, PRO-4X, S, SL, SV, SV/Comf | 8 Cyl 5.6L
View related parts
Nissan Rear Brake Pads Kit
Part Number: D4M60-9N00B
$79.22 MSRP: $114.73
You Save: $35.51 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Rear; Brake Pads, Rear Pads
- Position: Rear
- Replaces: D4M60-9N00A
Fits the following Nissan Models:
- Juke | 2011-2017 | Base, Luxury, Nismo, S, SL, SV, Upper | 4 Cyl 1.6L
- Leaf | 2011-2014 | S, SL, SV, Upper | Electric Motor
- Murano | 2009-2020 | CrossCabriolet, LE, LE/ROOF, Platinum, S, SL, SL/ROOF, SV | 4 Cyl 2.5L, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L
- Pathfinder | 2013-2020 | Platinum, Platinum Hybrid, S, SL, SL Hybrid, SV, SV Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5L, 6 Cyl 3.5 L GAS, 6 Cyl 3.5L
- Quest | 2011-2017 | LE, S, SL, SV | 6 Cyl 3.5L
View More
View related parts
Nissan Front Brake Pads Kit
Part Number: D1060-5RB0B
$74.31 MSRP: $107.63
You Save: $33.32 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Front; Brake Pads, Front Pads
- Position: Front
- Replaces: D1060-5RB0A
Fits the following Nissan Models:
- Kicks | 2018-2020 | S, SR, SR PLUS, SV | 4 Cyl 1.6 L GAS, 4 Cyl 1.6L
View related parts
Nissan Rear Disc Brake Pads Kit
Part Number: D4060-4BA0C
$76.21 MSRP: $110.38
You Save: $34.17 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Rear
- Position: Rear
- Replaced by: D4060-4CU2A
Fits the following Nissan Models:
- Rogue | 2016-2019 | S, SL, SV, SV Premium | 4 Cyl 2.5L
- Rogue Sport | 2017-2019 | S, SL, SV | 4 Cyl 2.0L
View related parts
Nissan Pad Kit-Disc Br
Part Number: D4060-6LA0A
$91.11 MSRP: $131.95
You Save: $40.84 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Pads, Rear Pads
Fits the following Nissan Models:
- Sentra | 2020-2025 | S, SR, SV | 4 Cyl 2.0 L GAS
View related parts
Nissan Rear Brake Pads Kit
Part Number: D4060-1MB0A
$82.06 MSRP: $118.85
You Save: $36.79 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Disc Brake,Rear; Brake Pads, Rear Pads
- Position: Rear
Fits the following Nissan Models:
- 370Z | 2009-2020 | 40th Anniversary Edition, Base, Heritage Edition, Nismo, Nismo Tech, Sport, Sport Tech, Sport Touring, Touring, Touring Sport | 6 Cyl 3.7 L GAS, 6 Cyl 3.7L
View related parts
Nissan Pad Kit-Disc Brake,Front
Part Number: D1060-6LE0A
$74.31 MSRP: $107.63
You Save: $33.32 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Pads, Front Pads
- Position: Front
Fits the following Nissan Models:
- Kicks | 2021-2024 | SR, SV | 4 Cyl 1.6 L GAS
- Sentra | 2020-2025 | S, SR, SV | 4 Cyl 2.0 L GAS
View related parts
Nissan Pad Kit-Disc Br
Part Number: D4060-6TA5A
$79.54 MSRP: $108.72
You Save: $29.18 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Pads, Rear Pads
- Replaced by: D4060-6TA5B
Fits the following Nissan Models:
- ARIYA | 2023-2024 | Empower+, Engage, Engage+, Evolve+, Platinum+, Venture+ | BATTERY EV (EV/BEV)
- Murano | 2025 | Platinum, SL, SV | 4 Cyl 2.0 L GAS
- Pathfinder | 2022-2025 | Platinum, Rock Creek, S, SL, SV | 6 Cyl 3.5 L GAS
View More
View related parts
Nissan Disc Brake Pad Kit
Part Number: D1M60-9FE0A
$81.69 MSRP: $118.32
You Save: $36.63 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: PAD KIT - DISC BRAKE; Brake Pads, Front Pads
- Replaces: D1060-ZC60J, D1060-ZC60A, D1060-9FE0A, D1060-1LA1A
Fits the following Nissan Models:
- Armada | 2020 | LE, Platinum, Platinum Reserve, SE, SE Off-Road, SL, SV, Titanium | 8 Cyl 5.6 L FLEX, 8 Cyl 5.6 L GAS

| Page 1 of 19 |Next >

1-20 of 365 Results

About Nissan Brake Pad Set

Too many accidents happen when the car cannot brake in time, and it is all about brake system. Brake pad set plays the most important role in the brake system in your Nissan. Actually, a brake pad set consists of a friction material and a brake caliper. When you press the pedal, the caliper starts to squeeze the brake pads, further leading to slow down the speed. Usually, brake pad set does not broke at once, and there is a process for it to fail. So when you drive your Nissan over 50,000 miles, or you can measure the pad is thinner than 0.2 inches, then you are supposed to change your brake pad set. We carry a huge selection of Nissan OEM brake pad set just for your convenience. You can browse here and find your favorite one and get it just by one clicking. We offer affordable price with high quality for you pleasure.

Nissan Brake Pad Set Parts Questions & Experts Answers

Disc Brake Pad Kit
44060-53F92
Q: How to check the pad lining thickness and replace the front Brake Pad Set for Nissan 240sx?
A:
To check the pad lining thickness, it is possible to do so without removing the pads, and the Brake Specifications chart provides the manufacturer's pad wear limit, although this may differ from state inspection laws. When replacing pads, inspect the rotor surfaces for scoring or wear, and remove them for resurfacing if they are badly scored. All four front brake pads must be replaced as a complete set, and bleeding the brake system should only be done if necessary. For the Type N22 Series, raise the front of the vehicle, remove the wheels, and take out the retaining clip and pad pins before removing the pads. To install, open the bleeder screw slightly, push the outer piston in, install the inner pad, and then the outer pad, applying grease to contact areas while avoiding the friction surfaces. For the Type CL22V Series, raise the front, remove the lower pin bolt, swing the cylinder body upward, and remove the pad retainer and pads without depressing the brake pedal. Clean the piston end, install the inner and outer pads, and tighten the pin bolt. For the Type AD22V Series, remove the road wheel, lower caliper guide pin, and rotate the caliper body upward to remove the pads. Clean the piston end, install the new pads, and tighten the guide pin bolt. For Types CL28VB, CL22VB, and CL25VB, raise the vehicle, remove the front wheel and lower pin bolt, swing the caliper body upward, and remove the pad retainers and shims. Check the fluid level in the master cylinder, use a C-clamp to press the caliper piston back, install new pads with new shims, torque the lower retaining bolt, and ensure the brakes are bled and adjusted as necessary before driving.
Rear Brake Pads Kit
D4M60-9N00B
Q: How to properly replace the rear Brake Pad Set on a Nissan Juke?
A:
Chock the front wheels, jack up the rear of the car, and support it on axle stands before removing the rear road wheels and fully releasing the handbrake. On one side of the vehicle, push the caliper piston into its bore by pulling the caliper outwards, then unscrew and remove the caliper lower guide pin bolt. Pivot the caliper body upwards to expose the brake pads, securing it in place without depressing the brake pedal, and take care not to strain the brake fluid hose. Note the locations and orientation of the shims and anti-rattle clips, then lift out the brake pads, shims, and clips. Separate the shims from the pads, noting their fitted position, and measure the thickness of each brake pad's friction material; if any pad is worn to the specified minimum thickness or less, all four pads must be renewed, and any fouled pads should also be replaced. If the pads are serviceable, clean them carefully, paying attention to the sides and back of the metal backing, and clean the anti-rattle clips, shims, and brake pad locations in the caliper body. Check that the rubber guide pin gaiters are undamaged, brush away dust and dirt from the caliper and piston, and inspect the dust seal and piston for damage or leaks. If new brake pads are to be fitted, push the caliper piston back into the cylinder using a G-clamp or suitable levers, monitoring the master cylinder reservoir to prevent spillage. Refit the upper and lower anti-rattle clips, apply anti-squeal brake grease to the contact surfaces of the pad backing plates, and refit the shims, ensuring no grease contacts the pad friction linings. Refit the pads and shims in their original positions, pivot the caliper back into place, and tighten the caliper lower guide pin bolt to the specified torque. Check that the caliper body slides smoothly on the guide pins, repeat the procedure on the remaining rear caliper, and after refitting both sets of front brake pads, depress the brake pedal repeatedly until normal pedal pressure is restored. Finally, refit the roadwheels, lower the vehicle to the ground, and check the brake hydraulic fluid level, keeping in mind that new pads will not provide full braking efficiency until they have bedded in, so avoid hard braking for the first hundred miles after renewal.