Question 1

How to raise the Nissan Altima and adjust the shift cable on the manual transmission?

Accepted Answer

Raise the vehicle and support it securely on jackstands. Remove the center console, then place the shifter in Neutral. For access to the top of the transaxle, remove the air filter housing and ducts. Detach the cables from the shift levers and brackets, followed by detaching the cables from the shift assembly. Remove the bracket that covers the grommet in the floor of the vehicle, then take out the grommet/retainer and pull the cables from the vehicle. The shifter can be removed if required, and installation is the reverse of removal, ensuring to adjust the select cable before reinstalling the center console. To adjust, remove the bezel from around the shift lever if not already done, place the transaxle in Neutral, and pry the select cable from the shifter with a screwdriver. Slide the lock to the released position, push out the adjustment button to release it, and snap the cable back onto the shifter. Hold the shift lever so the space between the shifter base and the reverse gate stopper is 1/4-inch, then push the adjustment button back in and slide the lock to the locked position. Finally, ensure the shifting action is smooth; if not, repeat the adjustment procedure.

Question 2

Are adjustments available for the shift cables on Nissan Versa?

Accepted Answer

Adjustments are not available for the shift cables. If the vehicle does not shift properly, check for bent brackets and verify the cables are correctly installed in the brackets and on the levers. Begin by raising the vehicle and supporting it securely on jackstands. For 2011 and earlier models, the shifter assembly and cables are one unit and cannot be replaced separately. Remove the battery, then take out the air filter housing and ducts for access to the top of the transaxle. Detach the cables from the shift lever on the transaxle, move the stopper on the side of the select cable connection forward, push in on the release button next to the stopper, and remove the cable from the select lever. Place the shifter in Neutral, then remove the center console and the four shifter assembly mounting bolts. Raise the vehicle again and support it securely on jackstands, then remove the exhaust system and heat shield from under the center of the vehicle to allow access to the shift cables. Remove the cable support bracket and the shift and select cables from the bracket, then remove the shifter and shift cables as an assembly from under the vehicle. Installation is the reverse of removal, ensuring to move the stopper into the locked position after connecting the select cable to the lever. For 2012 and later models, place the shifter in Neutral, remove the battery and battery tray, then detach the shift and select cables from the shift levers and brackets. Press the sides of the cable locks together to remove the shift and select cables from the bracket on the transaxle, then remove the center console. Pry off the shift and select cables from the shifter assembly, press the sides of the cable locks together again to remove the cables from the bracket on the shifter assembly, and then remove the four shifter assembly mounting bolts to take out the shifter assembly. Remove the exhaust system and heat shield from under the center of the vehicle to allow access to the shift cables, then remove the cable support bracket and the shift and select cables from the bracket, followed by removing the grommet retainer and pulling the cables from the vehicle. Installation is the reverse of removal.

Question 3

How to replace the shift cable on Nissan Sentra?

Accepted Answer

To replace the shift cable, position the gear selector in park and break the shift cable from the pivot and shift it to the down position to remove it from the bracket. Thirdly, the battery and the housing with air ducts should be unstalled to grant access to the top of the transaxle. Pull the cable away from the shift lever and the bracket fixed on the transaxle, lief then and jack up the vehicle and place it on several stands. Take off the exhaust and the heat shield located under the center of the car to gain access to the shift cable, after that, the client should unscrew the cable support bracket as well as the shift cable. Removing involves restoring the interior to the state it was before and the cable ought to be fine tuned after the installation. For adjustment, you need to take off the air filter housing, put the shift lever to the "P" position, slacken the shift cable to the manual lever locknut and confirm that the transaxle manual shift lever is fully in the Park position, before making the final adjustments. While the manual lever is held in position release the tension on the lock nut probably by rotating the lock nut counter clockwise and then shift the shape levers from "P" to "1", there should be no hard feeling or resistance on the lever and the shift indicator should be in harmony with the actual positions of the shift levers. Last of all, ensure that the starting of the engine is possible.

Genuine Nissan Shift Cable

173 Shift Cables found

Nissan Control Cable Assembly

Nissan Automatic Transmission Shifter Cable

Nissan Control Cable Assembly

Nissan Automatic Transmission Shifter Cable

Nissan Manual Transmission Control Cable Assembly

Nissan Control Cable Assembly

Nissan Automatic Transmission Shifter Cable

Nissan Shift Control Cable

Nissan Control Cable Assembly

Nissan Control Cable Assembly

Nissan Automatic Transmission Shifter Cable

Nissan Control Cable Assembly

Nissan Control Cable Assembly

Nissan Manual Transmission Control Cable Assembly

Nissan Shift Control Cable

Nissan Control Cable Assembly

Nissan Control Cable Assembly

Nissan Control Cable Assembly

Nissan Control Cable Assembly

Nissan Automatic Transaxle Shift Shifter Control Cable

About Nissan Shift Cable

Nissan Shift Cable Parts Questions & Experts Answers

Related Nissan Parts

Browse by Model